low profile vise

This topic has 9 replies, 5 voices, and was last updated 8 March 2020 at 06:26 by Mark Eisen.

Viewing 10 posts - 1 through 10 (of 10 total)

Author

Posts
11 October 2019 at 20:26 #432882
celso ari schlichting
Participant
@celsoarischlichting85092
Here's a video of the vise I made for the milling machine:

[youtube] https://youtu.be/–2ET20n344

strong hug
Celso Ari

Edited By celso ari schlichting on 11/10/2019 20:29:07
Advert

11 October 2019 at 20:26 #19496
celso ari schlichting
Participant
@celsoarischlichting85092
12 October 2019 at 06:17 #432903
Thor 🇳🇴
Participant
@thor
Nice work on the vise, must find time to make something similar for my small milling machine.

Thor
12 October 2019 at 09:54 #432919
SillyOldDuffer
Moderator
@sillyoldduffer
Good work again from Celso Ari. I'm always quietly impressed by his work.

Loads of good stuff is posted on the forum and then only admired silently. I hope this apparent lack of interest doesn't put anyone off. It's the audience, the British are famously undemonstrative!

Keep it coming.

Thanks,

Dave
12 October 2019 at 12:51 #432943
Howard Lewis
Participant
@howardlewis46836
NEAT!

You have used two pieces, with a moving jaw, where my "Infinite Vice" is in three parts.

Now you have made me another job on the Round Tuit; to mill a rebate inn the fixed and moving jaws, like yours, to reduce the need for parallels under the workpiece.

Did you dowel or key the jaws to the Tee slots?. Neater than the side cheeks on the jaws of mine for location!

Howard

Edited By Howard Lewis on 12/10/2019 12:52:46
12 October 2019 at 13:08 #432946
celso ari schlichting
Participant
@celsoarischlichting85092
Posted by Thor on 12/10/2019 06:17:10:

Nice work on the vise, must find time to make something similar for my small milling machine.

Thor

It is very versatile and works very well. Thanks for the comment. there are other mechanical projects on my YouTube page

Greetngs from Brazil

Celso Ari
12 October 2019 at 13:10 #432947
celso ari schlichting
Participant
@celsoarischlichting85092
Posted by SillyOldDuffer on 12/10/2019 09:54:17:

Good work again from Celso Ari. I'm always quietly impressed by his work.

Loads of good stuff is posted on the forum and then only admired silently. I hope this apparent lack of interest doesn't put anyone off. It's the audience, the British are famously undemonstrative!

Keep it coming.

Thanks,

Dave

Thanks friend Dave, your words are an incentive for me.
greetings from Brazil

Celso Ari
12 October 2019 at 13:17 #432948
celso ari schlichting
Participant
@celsoarischlichting85092
Posted by Howard Lewis on 12/10/2019 12:51:37:

NEAT!

You have used two pieces, with a moving jaw, where my "Infinite Vice" is in three parts.

Now you have made me another job on the Round Tuit; to mill a rebate inn the fixed and moving jaws, like yours, to reduce the need for parallels under the workpiece.

Did you dowel or key the jaws to the Tee slots?. Neater than the side cheeks on the jaws of mine for location!

Howard

Edited By Howard Lewis on 12/10/2019 12:52:46

Howard, I couldn't understand the question. can you do it again? My english is not good, we speak portuguese here in my country (translation problems he he)

greetings from Brazil

Celso Ari
12 October 2019 at 13:42 #432953
Howard Lewis
Participant
@howardlewis46836
Hi!

Your English is much better than my inability to speak Portugese!

How are jaws aligned to the table?

Are there keys to locate the jaw to the Tee slot?

Or do you have dowels under the jaws to locate inn then Tee slots?

Regards

Howard
8 March 2020 at 06:26 #456012
Mark Eisen
Participant
@markeisen61287
Most impressive Celso, will have to make one when I get back in to the shed.
Author

Posts