Fixed steady for WM210 lathe

This topic has 13 replies, 5 voices, and was last updated 3 September 2026 at 21:21 by Chris Kaminski.

Viewing 14 posts - 1 through 14 (of 14 total)

Author

Posts
3 September 2026 at 13:25 #863412
Chris Kaminski
Participant
@chriskaminski64716
Any users/owners of above mentioned WM210 lathe?

and more specifically fixed steady for it?

These fixed steadies are readily available form many usual sources and are perfect size match (at 105mm centre height) for either Emco8 or Prazimat lathe, but…

in the usual Chinese fashion casting is described as made from “metal”

Before I buy one to adapt for my Prazimat, I would like to know whether it is cast iron or aluminium?

(enquiries with sellers were inconclusive/not helpful)

and is it any good at all?
Advert

3 September 2026 at 15:20 #863422
JasonB
Moderator
@jasonb
Judging by the weight of the one that came with the Amadeal 210E that I had to review I would say definately cast iron. Give Luke or Hugh a bell at Amadeal as they sell the steadies separately unlike Warco who sell them complete with the lathe They will also confirm the material.

My larger Warco 280 steadies are iron.
3 September 2026 at 15:27 #863423
Chris Kaminski
Participant
@chriskaminski64716
On 3 September 2026 at 15:20 JasonB Said:

….I would say definitely cast iron….

My larger Warco 280 steadies are iron.

Thank you, will contact Amadeal.

I am, being careful because they are either described as “metal” or “aluminium” none mention “cast iron” and all photos look identical.

Did you try using the steady in your review?
3 September 2026 at 15:46 #863428
JasonB
Moderator
@jasonb
No
3 September 2026 at 15:56 #863430
mgnbuk
Participant
@mgnbuk
The similar pattern steady supplied with my Chester 7″ mini lathe is CI as is the larger, similar pattern, item supplied with my Warco GH600.

They work – but I prefer the hinged type (i.e. Myford 7 pattern) for easier access. Both the Chinese items are a bit loosely fitted together, with play in the adjusting screws on the fingers which makes them a bit fiddly to set up, but they do the job.

Nigel B.
3 September 2026 at 16:01 #863431
Chris Kaminski
Participant
@chriskaminski64716
On 3 September 2026 at 15:56 mgnbuk Said:

..with play in the adjusting screws on the fingers which makes them a bit fiddly to set up, but they do the job.

Thank you Nigel

That is what I suspected…
3 September 2026 at 17:02 #863438
Grindstone Cowboy
Participant
@grindstonecowboy
Blondihacks modified a Chinese steady, might be worth a look.

Rob
3 September 2026 at 17:58 #863440
old mart
Participant
@oldmart
As fixed steadies for the Smart & Brown model A are so expensive, I bought two Chinese cast iron steadies, a small C shaped one and a bigger hinged one. The bases were cut off and the legs milled and drilled to fit to an aluminium base, at the correct height. With another base they both fit the 12 x 24 Atlas bed. Of course you have to have a mill to do this.
3 September 2026 at 17:59 #863441
Chris Kaminski
Participant
@chriskaminski64716
On 3 September 2026 at 17:02 Grindstone Cowboy Said:

Thanks Rob!

These videos answered all the questions I had
3 September 2026 at 18:02 #863446
Chris Kaminski
Participant
@chriskaminski64716
On 3 September 2026 at 17:58 old mart Said:

As fixed steadies for the Smart & Brown model A are so expensive….

I like the white one and of course I’d have to do what you did with the bases as well
3 September 2026 at 18:04 #863447
old mart
Participant
@oldmart
I found some more pictures. The bigger one came with bronze fingers and I made another set with little ball races as shown.
3 September 2026 at 18:19 #863452
Chris Kaminski
Participant
@chriskaminski64716
On 3 September 2026 at 18:04 old mart Said:

I found some more pictures…

Thank you!
3 September 2026 at 18:23 #863453
old mart
Participant
@oldmart
More pictures, the little steady can be bolted either side of the base and the undersides show the nut arrangement for QD attachment with a captive locknut and shaped to go between the bed rails, much better than groping underneath to tighten and remove. I hope it gives a few tips on designs that work.
3 September 2026 at 21:21 #863472
Chris Kaminski
Participant
@chriskaminski64716
Max Grant has couple of good videos on adapting secondhand steady to another lathe:

enjoy 👍
Author

Posts