INT 30

INT 30

This topic has 4 replies, 4 voices, and was last updated 13 February 2014 at 20:05 by JasonB.

Viewing 5 posts - 1 through 5 (of 5 total)

Author

Posts
13 February 2014 at 19:49 #143809
Kenneth Deighton
Participant
@kennethdeighton43272
I wish to make a NT30 Arbor with a 1.125" x 12 tpi end to utilize my Myford equipment on my Tom Senior milling machine , am I correct that the angle from the horizontal shoulder to the taper is 80 degrees ?

Thanks..
Advert

13 February 2014 at 19:49 #17300
Kenneth Deighton
Participant
@kennethdeighton43272
13 February 2014 at 19:59 #143811
Keith Long
Participant
@keithlong89920
The Model Engineers Handbook (3rd Ed) gives the taper as 7 in 24 on diameter – doesn't give an angular measurement at all.

Keith
13 February 2014 at 20:01 #143812
mgnbuk
Participant
@mgnbuk
http://www.tools-n-gizmos.com/specs/Tapers.html
13 February 2014 at 20:05 #143813
JasonB
Moderator
@jasonb
That ratio would give about 73.78deg
Author

Posts

Viewing 5 posts - 1 through 5 (of 5 total)

Please log in to reply to this topic. Registering is free and easy using the links on the menu at the top of this page.

Code of Conduct

Latest Replies

Viewing 25 topics - 1 through 25 (of 25 total)

- Topic
- Voices
- Posts
- Last Post
- Chinese EV teardown
  Started by: Michael Gilligan in: The Tea Room
- 3
- 3
- 21 September 2026 at 21:30
  Andrew Tinsley
- Free issues
  Started by: doreen hynes in: General Questions
- 4
- 5
- 21 September 2026 at 21:18
  Andrew Tinsley
- New Myford 7 DRO article 1 2
  Started by: Bob Worsley in: Electronics in the Workshop
- 8
- 29
- 21 September 2026 at 20:17
  Robert Atkinson 2
- Microscope eyepieces
  Started by: gerry madden in: Clocks and Scientific Instruments
- 6
- 10
- 21 September 2026 at 19:39
  peak4
- Ideas needed for problem wth Tom Senior E type Mill
  Started by: Mike Crossfield in: Manual machine tools
- 10
- 22
- 21 September 2026 at 18:32
  old mart
- Drive coil ampere turns for seconds pendulum 1 2
  Started by: carlw in: Clocks and Scientific Instruments
- 6
- 34
- 21 September 2026 at 18:20
  John Purdy
- The saga of the wayward SX2P mini mill
  Started by: Howi in: Manual machine tools
- 3
- 4
- 21 September 2026 at 17:24
  Robert Atkinson 2
- A little help
  Started by: leeco123 in: Introduce Yourself – New members start here!
- 3
- 4
- 21 September 2026 at 16:14
  leeco123
- Crucible Furnace
  Started by: BOB BLACKSHAW 1 in: General Questions
- 7
- 11
- 21 September 2026 at 16:07
  Engine Builder
- Computer advice needed
  Started by: JohnF in: The Tea Room
- 11
- 11
- 21 September 2026 at 13:42
  Wink Hackman
- Project anyone
  Started by: Dalboy in: General Questions
- 5
- 5
- 21 September 2026 at 13:29
  Bazyle
- Article about Steam Luanches
  Started by: dbs88 in: Model Engineer.
- 7
- 19
- 21 September 2026 at 11:39
  noel shelley
- Arc closure and popularity of Chineese lathes
  Started by: File Handle in: The Tea Room
- 7
- 8
- 21 September 2026 at 10:40
  Nicholas Farr
- The Big St Albans Model Show
  Started by: Bazyle in: Exhibitions, Shows and Club Events
- 1
- 1
- 21 September 2026 at 10:18
  Bazyle
- Tom Thumb Toolpost Grinder
  Started by: Phil P in: Workshop Tools and Tooling
- 3
- 3
- 21 September 2026 at 09:05
  JohnF
- Wilesco rebuild
  Started by: harryssteam in: Work In Progress and completed items
- 2
- 2
- 21 September 2026 at 08:14
  Nigel Bennett
- Octopus Heat Pump 1 2 3 4
  Started by: Michael Gilligan in: The Tea Room
- 25
- 89
- 21 September 2026 at 06:29
  Michael Gilligan
- Doorbells
  Started by: Michael Gilligan in: The Tea Room
- 7
- 13
- 21 September 2026 at 06:24
  Michael Gilligan
- Suzanne
  Started by: Steve Huckins in: Work In Progress and completed items
- 5
- 8
- 20 September 2026 at 21:25
  Engine Builder
- Bridgeport Milling Machine feed control module 1 2
  Started by: Mark Willis in: Workshop Tools and Tooling
- 14
- 26
- 20 September 2026 at 19:53
  niklas 1512
- Harrison L5 mk2 or not
  Started by: sean logie in: Workshop Tools and Tooling
- 4
- 4
- 20 September 2026 at 19:22
  Andy Stopford
- Milling machine spindle speed readout problem
  Started by: Steve Huckins in: General Questions
- 2
- 2
- 20 September 2026 at 15:10
  Clive Brown 1
- Mini lathes I need to look into
  Started by: mcenhillk in: Manual machine tools
- 14
- 18
- 20 September 2026 at 08:06
  Dell
- End mill sharpening 1 2
  Started by: petro1head in: General Questions
- 16
- 32
- 19 September 2026 at 23:30
  Nigel Graham 2
- My week this week! My workshop videos 1 2 … 13 14
  Started by: Phil Whitley in: The Tea Room
- 16
- 332
- 19 September 2026 at 19:24
  Phil Whitley

Viewing 25 topics - 1 through 25 (of 25 total)

View full reply list.

Latest Issue

October 2026

Buy Latest/Back Issues

Newsletter Sign-up

Latest Replies