Beginners questions

Beginners questions

This forum has 7,308 topics, 113,086 replies, and was last updated 14 June 2026 at 10:18 by alecs.

Viewing 25 topics - 126 through 150 (of 7,308 total)

← 1 2 3 … 5 6 7 … 291 292 293 →

- Topic
- Voices
- Posts
- Last Post
- Boxford lathe & vertical mill VFD conversion help with start stop
  Started by: Andrew Schofield
- 8
- 10
- 5 July 2025 at 11:39
  Clive Brown 1
- Haining vertical dairy engine boiler.
  Started by: apprentice
- 3
- 7
- 2 July 2025 at 20:52
  JasonB
- Motor won’t start
  Started by: Rowan Sylvester-Bradley
- 9
- 9
- 2 July 2025 at 17:30
  larry phelan 1
- Wiring up a single phase AC motor with 4 wires
  Started by: ell81
- 6
- 8
- 30 June 2025 at 19:49
  Howard Lewis
- Workshop Practice Series – Books
  Started by: flatline
- 4
- 5
- 24 June 2025 at 18:30
  duncan webster 1
- First cuts with the lathe 1 2 3
  Started by: Chris12
- 22
- 53
- 23 June 2025 at 22:47
  Andrew Crow
- Sieg C1 lathe autofeed and screw cutting 1 2
  Started by: Rob Athome
- 16
- 41
- 23 June 2025 at 22:16
  Martin of Wick
- Milling in the lathe – Vertical slide 1 2
  Started by: Chris12
- 12
- 31
- 20 June 2025 at 18:44
  Roger B
- Is there an alternative to tufnol strip for springing
  Started by: steve2250
- 7
- 11
- 19 June 2025 at 12:20
  Dave Wootton
- Rotary table question.
  Started by: larry phelan 1
- 7
- 16
- 19 June 2025 at 08:51
  larry phelan 1
- Motorcycle starter motors – any general workshop uses?
  Started by: Robin Graham
- 10
- 14
- 18 June 2025 at 20:58
  John Haine
- Magnetic bases – stored on or off? 1 2
  Started by: Grindstone Cowboy
- 25
- 45
- 16 June 2025 at 12:25
  Robert Atkinson 2
- Stuart No.1 on a Myford Super-7??
  Started by: flatline
- 5
- 8
- 13 June 2025 at 16:59
  flatline
- Hydraulic hand pump – air release? What are these screws?
  Started by: ell81
- 7
- 10
- 12 June 2025 at 17:47
  Diogenes
- crompton motor and dewhurst switch problems
  Started by: mike smith 5
- 6
- 7
- 11 June 2025 at 21:17
  noel shelley
- First lathe – warco 180/210
  Started by: Chris12
- 8
- 13
- 7 June 2025 at 17:18
  Nick Wheeler
- Plain bearing play
  Started by: Sonic Escape
- 5
- 8
- 7 June 2025 at 10:07
  bernard towers
- Lathe spindle bearings
  Started by: Sonic Escape
- 10
- 21
- 7 June 2025 at 09:20
  jamesp1
- 1950 Myford/Drummond type m advice
  Started by: jimmyjaffa
- 7
- 16
- 5 June 2025 at 19:25
  Howard Lewis
- Drawing Projections 1 2 … 6 7
  Started by: Wolfie
- 89
- 172
- 29 May 2025 at 17:59
  SillyOldDuffer
- ‘STIFF’ Compound Slide 1 2
  Started by: kevian64
- 16
- 28
- 29 May 2025 at 15:35
  Pete
- Help and advice please
  Started by: acklam65
- 7
- 12
- 22 May 2025 at 10:47
  Pete
- Degreasing internal 3mm thread
  Started by: Mike Quinn 1
- 12
- 15
- 18 May 2025 at 07:02
  Mike Quinn 1
- Help in/nr Hereford
  Started by: simonj34
- 3
- 4
- 15 May 2025 at 16:44
  Howard Lewis
- Removing side tank hand pump
  Started by: Mark Salzedo 1
- 4
- 9
- 15 May 2025 at 16:09
  Mark Salzedo 1

Viewing 25 topics - 126 through 150 (of 7,308 total)

← 1 2 3 … 5 6 7 … 291 292 293 →

You must be logged in to create new topics.

Latest Issue

May 2026

Buy Latest/Back Issues

Newsletter Sign-up