Making steel channel

This topic has 4 replies, 3 voices, and was last updated 29 March 2016 at 18:41 by Mark P..

Viewing 5 posts - 1 through 5 (of 5 total)

Author

Posts
29 March 2016 at 17:33 #232302
Mark P.
Participant
@markp
Hi all, I need to make 2 pices of mild steel channel 44x25x4x300mm long if I machine it from 25x50mm bright flat will I end up with a twisted mess?
Regards Mark P.
Advert

29 March 2016 at 17:33 #15841
Mark P.
Participant
@markp
29 March 2016 at 17:37 #232305
Michael Gilligan
Participant
@michaelgilligan61133
Very probably.

I think it would need some Stress-Relief first … a night in the embers of a fire might help.

MichaelG.
29 March 2016 at 17:37 #232306
JasonB
Moderator
@jasonb
Cut down two bits of angle and weld them into a U. If you like making swarf then get black flat bar as its less likely to move. I have used this e-bay seller a few times for black bar and angle, also does 50x25x5 chanel if you could get away with 48mm x 24 x 4 after a skim

Edited By JasonB on 29/03/2016 17:42:12
29 March 2016 at 18:41 #232327
Mark P.
Participant
@markp
Thanks for the replies just as I thought a mangled mess! Will have a look at that supplier Jason. If all fails I will try black bar.
Regards Mark P.
Author

Posts

Viewing 5 posts - 1 through 5 (of 5 total)

Please log in to reply to this topic. Registering is free and easy using the links on the menu at the top of this page.

Advert

Latest Replies

Viewing 25 topics - 1 through 25 (of 25 total)

- Topic
- Voices
- Posts
- Last Post
- 2inch Fowler plans
  Started by: bob53page in: Traction engines
- 6
- 11
- 5 November 2026 at 20:56
  JasonB
- Richard Simmonds’ “How To Make A Weight Driven Clock”
  Started by: iacooper in: Clocks and Scientific Instruments
- 8
- 12
- 5 November 2026 at 20:52
  Pete
- New Mystery Lathe
  Started by: mart7mcfl7 in: Manual machine tools
- 4
- 5
- 5 November 2026 at 20:27
  Dave Halford
- Model Turbines 1 2 … 26 27
  Started by: Turbine Guy in: Stationary engines
- 28
- 664
- 5 November 2026 at 20:02
  Turbine Guy
- Building the V-Twin “Kelsey” 1 2 … 4 5
  Started by: JasonB in: Stationary engines
- 18
- 123
- 5 November 2026 at 19:20
  Jim Nic
- BCA MK III Jig Borer
  Started by: pjh in: Help and Assistance! (Offered or Wanted)
- 7
- 10
- 5 November 2026 at 19:19
  duncan webster 1
- Minnie Traction Engine – Damper Hinge Plate
  Started by: Dominic Bramley in: Traction engines
- 6
- 15
- 5 November 2026 at 18:56
  Dominic Bramley
- Onshape Learning
  Started by: BOB BLACKSHAW 1 in: CAD – Technical drawing & design
- 5
- 11
- 5 November 2026 at 18:05
  Engine Builder
- Unimat 3 baseplate
  Started by: mart7mcfl7 in: Manual machine tools
- 4
- 9
- 5 November 2026 at 17:41
  mart7mcfl7
- WAR FINISH
  Started by: Speedy Builder5 in: The Tea Room
- 11
- 12
- 5 November 2026 at 16:58
  not done it yet
- Richard B’s Minnie. 1 2
  Started by: Richard B in: Traction engines
- 4
- 26
- 5 November 2026 at 16:30
  Richard B
- Unusual dual speed pulley on motor
  Started by: gerry madden in: Manual machine tools
- 10
- 17
- 5 November 2026 at 16:28
  Macolm
- Most used ‘rubbish’ tool
  Started by: jaCK Hobson in: The Tea Room
- 9
- 12
- 5 November 2026 at 14:43
  Vic
- Shape of Boxford fixed steady blocks
  Started by: Grindstone Cowboy in: Beginners questions
- 7
- 9
- 5 November 2026 at 14:12
  Grindstone Cowboy
- A small Hobbing Machine
  Started by: Michael Gilligan in: Workshop Tools and Tooling
- 3
- 5
- 5 November 2026 at 14:08
  Michael Gilligan
- Micrometer ratchets
  Started by: Graeme Seed in: Workshop Tools and Tooling
- 11
- 17
- 5 November 2026 at 13:09
  Graeme Seed
- Mitotoyo dial caliper battery or innards.
  Started by: Clive Farrar in: General Questions
- 10
- 12
- 5 November 2026 at 09:01
  Hollowpoint
- 3d Printed Carriage Stop for Warco WM180
  Started by: James A in: Workshop Tools and Tooling
- 1
- 1
- 5 November 2026 at 07:51
  James A
- Mitutoyo Dial Calliper dial?
  Started by: Bo’sun in: Workshop Tools and Tooling
- 4
- 7
- 4 November 2026 at 22:03
  Pete
- SOLIDWORKS for MAKERS
  Started by: Paul Lousick in: CAD – Technical drawing & design
- 2
- 3
- 4 November 2026 at 21:54
  Paul Lousick
- 127t Gear With ⅞” Shaft and Keyway – Which Lathe?
  Started by: Captain Barnacles in: Workshop Tools and Tooling
- 15
- 24
- 4 November 2026 at 19:56
  Captain Barnacles
- What Did You Do Today 2026 1 2 … 9 10
  Started by: JasonB in: The Tea Room
- 56
- 247
- 4 November 2026 at 17:50
  Nigel Graham 2
- help please in identifying
  Started by: John Holloway in: General Questions
- 4
- 9
- 4 November 2026 at 16:43
  renardiere7
- Mini ER11 milling/drilling unit
  Started by: YouraT in: Manual machine tools
- 5
- 9
- 4 November 2026 at 12:05
  bernard towers
- Lathe improvements? 1 2 … 5 6
  Started by: Niels Abildgaard in: Manual machine tools
- 24
- 130
- 4 November 2026 at 09:14
  Niels Abildgaard

Making steel channel

Making steel channel

Latest Replies

Latest Issue

November 2026

Newsletter Sign-up

Latest Replies