Polly engineering web site

Polly engineering web site

This topic has 2 replies, 3 voices, and was last updated 9 November 2023 at 17:40 by peak4.

Viewing 3 posts - 1 through 3 (of 3 total)

Author

Posts
21 October 2023 at 10:32 #678350
Eric Cox
Participant
@ericcox50497
Does any one know the web address for Polly model engineering as Pollymodelengineering.co.uk has been hacked
Advert

21 October 2023 at 11:28 #678461
JasonB
Moderator
@jasonb
It’s not been hacked, just showing up an unsecure, overide that and you can get to the site OK as I have just done so
9 November 2023 at 17:40 #689212
peak4
Participant
@peak4
I had the same and accessed the site fine like Jason, however, it’s now been replaced with a different site, at a different web address, as well as new premises just outside Cromford.

Now Polly-Me

Bill
Author

Posts

Viewing 3 posts - 1 through 3 (of 3 total)

Please log in to reply to this topic. Registering is free and easy using the links on the menu at the top of this page.

Code of Conduct

Latest Replies

Viewing 25 topics - 1 through 25 (of 25 total)

- Topic
- Voices
- Posts
- Last Post
- Magnetic bases – stored on or off?
  Started by: Grindstone Cowboy in: Beginners questions
- 12
- 16
- 13 June 2025 at 02:53
  Steviegtr
- What Did You Do Today 2025 1 2 … 5 6
  Started by: JasonB in: The Tea Room
- 30
- 137
- 12 June 2025 at 23:49
  Nigel Graham 2
- Boxford Cud or ML7 1 2
  Started by: Trevor Howley in: General Questions
- 23
- 48
- 12 June 2025 at 23:42
  Andrew Crow
- Drilling Holes In Aluminium Tube
  Started by: Peter Goodchild in: General Questions
- 9
- 16
- 12 June 2025 at 23:37
  duncan webster 1
- 30w low voltage PWM controller 1 2 3
  Started by: Michael Gilligan in: Electronics in the Workshop
- 8
- 56
- 12 June 2025 at 22:58
  SillyOldDuffer
- Mystery Object Quiz
  Started by: Robert Atkinson 2 in: The Tea Room
- 11
- 19
- 12 June 2025 at 21:00
  Robert Atkinson 2
- Chester Champion mill 3 phase questions
  Started by: martian in: Electronics in the Workshop
- 9
- 13
- 12 June 2025 at 20:14
  martian
- Tool post drill? 1 2
  Started by: Andrew Tinsley in: Workshop Tools and Tooling
- 17
- 26
- 12 June 2025 at 19:36
  Michael Gilligan
- Dead flies on the front of the car
  Started by: Plasma in: The Tea Room
- 15
- 16
- 12 June 2025 at 19:33
  JasonB
- Hydraulic hand pump – air release? What are these screws?
  Started by: ell81 in: Beginners questions
- 7
- 10
- 12 June 2025 at 17:47
  Diogenes
- Searching for leak proof quarter turn water shut off valves
  Started by: Greensands in: Hints And Tips for model engineers
- 5
- 8
- 12 June 2025 at 14:45
  duncan webster 1
- DIY steel hardening
  Started by: Bevel in: Materials
- 12
- 20
- 12 June 2025 at 12:17
  JasonB
- Need help choosing a lathe chuck 1 2
  Started by: th1980 in: Workshop Tools and Tooling
- 20
- 31
- 12 June 2025 at 10:29
  SillyOldDuffer
- A modern mystery (Yanmar injectors)
  Started by: Fulmen in: The Tea Room
- 7
- 19
- 12 June 2025 at 09:00
  Fulmen
- New Warco D330 – Some Advice Please
  Started by: Mark Slatter in: Manual machine tools
- 14
- 21
- 12 June 2025 at 08:21
  Mark Slatter
- Sieg C1 lathe autofeed and screw cutting
  Started by: Rob Athome in: Beginners questions
- 13
- 25
- 12 June 2025 at 00:16
  th1980
- Which motor ?
  Started by: here again in: Manual machine tools
- 8
- 24
- 11 June 2025 at 23:51
  Bazyle
- Hints and tips
  Started by: larry phelan 1 in: Hints And Tips for model engineers
- 4
- 4
- 11 June 2025 at 23:33
  Nigel Graham 2
- Myford service engineer
  Started by: Nic Bertelsen in: General Questions
- 8
- 15
- 11 June 2025 at 22:08
  old mart
- crompton motor and dewhurst switch problems
  Started by: mike smith 5 in: Beginners questions
- 6
- 7
- 11 June 2025 at 21:17
  noel shelley
- Is Evo-stik impact adhesive good for wood to plastic? Is bond long lasting? 1 2
  Started by: Simon Robinson 4 in: The Tea Room
- 15
- 28
- 11 June 2025 at 19:44
  Colin Bishop
- Any good used lathes contacts in Norfolk
  Started by: messy457 in: Introduce Yourself – New members start here!
- 7
- 11
- 11 June 2025 at 18:40
  Richard Bartholomew 3
- Selling Small Cutters?
  Started by: Vic in: The Tea Room
- 3
- 3
- 11 June 2025 at 16:26
  Michael Gilligan
- New Member from Edinburgh | Interested in Learning More
  Started by: williamadam1 in: Introduce Yourself – New members start here!
- 5
- 5
- 11 June 2025 at 15:08
  Howard Lewis
- Model dynamo drawings
  Started by: Dougie Swan in: General Questions
- 7
- 20
- 11 June 2025 at 13:46
  Scrumpy

Viewing 25 topics - 1 through 25 (of 25 total)

View full reply list.

Latest Issue

June 2025

Buy Latest/Back Issues

Newsletter Sign-up

Latest Replies