Looking for 0.001″ resolution carbon fibre digital calipers

Looking for 0.001″ resolution carbon fibre digital calipers

Home › Forums › Workshop Tools and Tooling › Looking for 0.001″ resolution carbon fibre digital calipers

Viewing 15 posts - 1 through 15 (of 15 total)
  • Author
    Posts
  • #620085
    Greensands
    Participant
      @greensands

      I recently searched for 0-6” carbon fibre (cheapo) digital callipers priced typically within the price range £5 to £15 but could only find, perhaps not unreasonably, units having a resolution 0.010”. Anyone know if they are available offering 0.001” resolution within a similar price bracket or is this expecting too much?

      #20836
      Greensands
      Participant
        @greensands
        #620093
        Mick B1
        Participant
          @mickb1
          Posted by Greensands on 07/11/2022 15:30:29:

          I recently searched for 0-6” carbon fibre (cheapo) digital callipers priced typically within the price range £5 to £15 but could only find, perhaps not unreasonably, units having a resolution 0.010”. Anyone know if they are available offering 0.001” resolution within a similar price bracket or is this expecting too much?

          I think the bold bit's key. I don't know its modulus of elasticity or owt like that, but I wouldn't expect carbon fibre to have the rigidity to work to a thou with any reliability.

          #620094
          Jelly
          Participant
            @jelly

            Carbon Fibre can be very rigid indeed, and interestingly you can control the rigidity of the part in each axis by manipulating the way it's laid up…

            But I do find it extremely unlikely that carbon fibre that rigid can be manufactured for £15 profitably…

            #620099
            Michael Gilligan
            Participant
              @michaelgilligan61133
              Posted by Jelly on 07/11/2022 16:41:13:

              Carbon Fibre can be very rigid indeed, and interestingly you can control the rigidity of the part in each axis by manipulating the way it's laid up…

              But I do find it extremely unlikely that carbon fibre that rigid can be manufactured for £15 profitably…

              .

              Yes … most unlikely !!

              A few months back, I bought some cheap ‘carbon fibre’ tweezers

              Most of then were broken when they arrived … presumably because the mailer that they were in had gone through the franking machine dont know

              Inspection showed them to be some sort of brittle plastic ‘reinforced’ with chopped-strand rovings of carbon fibre, in lengths too short to be useful.

              … the complete antithesis of a fully ‘engineered’ filament-wound product.

              MichaelG.

              .

              Edit: __ Temus fugit !! this photo is a year old :

              1b6cb8b0-fc54-4067-8146-89c162d5d107.jpeg

               

              Edited By Michael Gilligan on 07/11/2022 17:12:31

              #620102
              Greensands
              Participant
                @greensands

                General thought inspired by the photo shown on Page 581 of the Model Engineer No. 4702, 21st Oct – 3rd Nov 2022 where the author refers to the use of an inexpensive digital caliper for use in a DRO lathe application.

                #620121
                Brian G
                Participant
                  @briang

                  Zoro offer a "Senator Polycal Digital Caliper" at £15.99 inc. VAT with a resolution of 0.01mm / 0.005" but this appears to be polycarbonate like the similar (identical?) M&W one. I wasn't impressed by the claimed accuracy of +/-0.02mm / 0.008", but even a Mitutoyo caliper costing 10 times the price doesn't claim to be more accurate, so I guess it is in the nature of calipers.

                  Brian G

                  #620129
                  old mart
                  Participant
                    @oldmart

                    I wonder how resistant to abrasion the jaws are? I wouldn't like to use them on anything harder than wood.

                    #620130
                    Greensands
                    Participant
                      @greensands

                      For the application in mind i.e. a lathe DRO (See ME 4702), the jaw hardness is irrelevant and can in fact be sawn/ground off as they would simply get in the way.

                      #620133
                      DiogenesII
                      Participant
                        @diogenesii

                        Chronos do a steel one but you'd have to shell out a whole £22..

                        Chronos Electronic Digital Caliper 6" / 150mm

                        ..they claim 0.01mm /5 tenths resolution, 0.03mm / one thou accuracy..

                        #620140
                        Peter Cook 6
                        Participant
                          @petercook6

                          You only need the slider and the electronics. I used the bits from a set that the plastic case had broken, and 3D printed a replacement housing.

                          electronics covers.jpg

                          Works well as a cross-slide DRO.

                          PS Get a set that retain the zero when they switch off. The ones that reset to zero when you switch them back on are a pain as a DRO.

                          Edited By Peter Cook 6 on 07/11/2022 23:04:34

                          #623934
                          DiogenesII
                          Participant
                            @diogenesii
                            #624150
                            Mick B1
                            Participant
                              @mickb1
                              Posted by DiogenesII on 07/12/2022 17:26:15:

                              Just found these at RDG;

                              Dasqua Plastic 150mm caliper claims 1/2 a thou.

                              Amazing! Well done – I'm seriously tempted, just to play with it and see if it's really any good.

                              Just gotta get the Expenditure Appropriation through now…

                              laugh

                              #624152
                              Tony Pratt 1
                              Participant
                                @tonypratt1

                                All I can say is why, why, why?

                                Tony

                                #624154
                                Robert Atkinson 2
                                Participant
                                  @robertatkinson2
                                  Posted by DiogenesII on 07/12/2022 17:26:15:

                                  Just found these at RDG;

                                  Dasqua Plastic 150mm caliper claims 1/2 a thou.

                                  Hmm, I don't see any accuracy claim, just a "graduation" of 0.0005".

                                  Assuming this means a resolution of 0.0005" then the accuracy can not be 0.0005" because of the quantisation error of +- 0.0005" plus all the other error sources.

                                Viewing 15 posts - 1 through 15 (of 15 total)
                                • Please log in to reply to this topic. Registering is free and easy using the links on the menu at the top of this page.

                                Latest Replies

                                Viewing 25 topics - 1 through 25 (of 25 total)
                                Viewing 25 topics - 1 through 25 (of 25 total)

                                View full reply list.