Harold Hall’s Mill end and side sharpener jig.

Harold Hall’s Mill end and side sharpener jig.

This topic has 1 reply, 1 voice, and was last updated 29 January 2020 at 23:30 by David Caunt.

Viewing 2 posts - 1 through 2 (of 2 total)

Author

Posts
29 January 2020 at 23:30 #27116
David Caunt
Participant
@davidcaunt67674
Is length of the collet draw bar correct on the drawing?
Advert

29 January 2020 at 23:30 #449743
David Caunt
Participant
@davidcaunt67674
As a way of getting used to using a mill and lathe I'm working my way through Harold's book on sharpening tools by making the items in it.

I've checked and rechecked the parts against the drawings and my collet draw bar still sticks out the end so it would never pull in the collet.

I've tried searching through the forum to see if the subject has been broached before without any luck.

Has anybody had a similar problem?
Author

Posts

Viewing 2 posts - 1 through 2 (of 2 total)

Please log in to reply to this topic. Registering is free and easy using the links on the menu at the top of this page.

Code of Conduct

Latest Replies

Viewing 25 topics - 1 through 25 (of 25 total)

- Topic
- Voices
- Posts
- Last Post
- Magnetic bases – stored on or off?
  Started by: Grindstone Cowboy in: Beginners questions
- 12
- 16
- 13 June 2025 at 02:53
  Steviegtr
- What Did You Do Today 2025 1 2 … 5 6
  Started by: JasonB in: The Tea Room
- 30
- 137
- 12 June 2025 at 23:49
  Nigel Graham 2
- Boxford Cud or ML7 1 2
  Started by: Trevor Howley in: General Questions
- 23
- 48
- 12 June 2025 at 23:42
  Andrew Crow
- Drilling Holes In Aluminium Tube
  Started by: Peter Goodchild in: General Questions
- 9
- 16
- 12 June 2025 at 23:37
  duncan webster 1
- 30w low voltage PWM controller 1 2 3
  Started by: Michael Gilligan in: Electronics in the Workshop
- 8
- 56
- 12 June 2025 at 22:58
  SillyOldDuffer
- Mystery Object Quiz
  Started by: Robert Atkinson 2 in: The Tea Room
- 11
- 19
- 12 June 2025 at 21:00
  Robert Atkinson 2
- Chester Champion mill 3 phase questions
  Started by: martian in: Electronics in the Workshop
- 9
- 13
- 12 June 2025 at 20:14
  martian
- Tool post drill? 1 2
  Started by: Andrew Tinsley in: Workshop Tools and Tooling
- 17
- 26
- 12 June 2025 at 19:36
  Michael Gilligan
- Dead flies on the front of the car
  Started by: Plasma in: The Tea Room
- 15
- 16
- 12 June 2025 at 19:33
  JasonB
- Hydraulic hand pump – air release? What are these screws?
  Started by: ell81 in: Beginners questions
- 7
- 10
- 12 June 2025 at 17:47
  Diogenes
- Searching for leak proof quarter turn water shut off valves
  Started by: Greensands in: Hints And Tips for model engineers
- 5
- 8
- 12 June 2025 at 14:45
  duncan webster 1
- DIY steel hardening
  Started by: Bevel in: Materials
- 12
- 20
- 12 June 2025 at 12:17
  JasonB
- Need help choosing a lathe chuck 1 2
  Started by: th1980 in: Workshop Tools and Tooling
- 20
- 31
- 12 June 2025 at 10:29
  SillyOldDuffer
- A modern mystery (Yanmar injectors)
  Started by: Fulmen in: The Tea Room
- 7
- 19
- 12 June 2025 at 09:00
  Fulmen
- New Warco D330 – Some Advice Please
  Started by: Mark Slatter in: Manual machine tools
- 14
- 21
- 12 June 2025 at 08:21
  Mark Slatter
- Sieg C1 lathe autofeed and screw cutting
  Started by: Rob Athome in: Beginners questions
- 13
- 25
- 12 June 2025 at 00:16
  th1980
- Which motor ?
  Started by: here again in: Manual machine tools
- 8
- 24
- 11 June 2025 at 23:51
  Bazyle
- Hints and tips
  Started by: larry phelan 1 in: Hints And Tips for model engineers
- 4
- 4
- 11 June 2025 at 23:33
  Nigel Graham 2
- Myford service engineer
  Started by: Nic Bertelsen in: General Questions
- 8
- 15
- 11 June 2025 at 22:08
  old mart
- crompton motor and dewhurst switch problems
  Started by: mike smith 5 in: Beginners questions
- 6
- 7
- 11 June 2025 at 21:17
  noel shelley
- Is Evo-stik impact adhesive good for wood to plastic? Is bond long lasting? 1 2
  Started by: Simon Robinson 4 in: The Tea Room
- 15
- 28
- 11 June 2025 at 19:44
  Colin Bishop
- Any good used lathes contacts in Norfolk
  Started by: messy457 in: Introduce Yourself – New members start here!
- 7
- 11
- 11 June 2025 at 18:40
  Richard Bartholomew 3
- Selling Small Cutters?
  Started by: Vic in: The Tea Room
- 3
- 3
- 11 June 2025 at 16:26
  Michael Gilligan
- New Member from Edinburgh | Interested in Learning More
  Started by: williamadam1 in: Introduce Yourself – New members start here!
- 5
- 5
- 11 June 2025 at 15:08
  Howard Lewis
- Model dynamo drawings
  Started by: Dougie Swan in: General Questions
- 7
- 20
- 11 June 2025 at 13:46
  Scrumpy

Viewing 25 topics - 1 through 25 (of 25 total)

View full reply list.

Latest Issue

June 2025

Buy Latest/Back Issues

Newsletter Sign-up

Latest Replies