Harrison L5 thread cutting

Advert

New Replies

Report Bug

Help/FAQs

Harrison L5 thread cutting

This topic has 6 replies, 5 voices, and was last updated 12 June 2019 at 16:49 by Nigel Graham 2.

Viewing 7 posts - 1 through 7 (of 7 total)

Author

Posts
17 May 2019 at 23:17 #409711
Garry Scott 1
Participant
@garryscott1
Hello everyone,

To start I am a complete novice and never turned in the past but I've always wanted to so I bought a Harrison L5 lathe.

Because I'm new to all this I need abit of help with the screw cutting element of the lathe.
1. The information plate inside the gear cover is missing so if anyone could take a photo of there's that would be appreciated.
2. I would like to cut metric threads and I have no idea what gears I should be looking for could someone please offer some advise.
Thank you all in advance.

Garry
Advert

17 May 2019 at 23:17 #33399
Garry Scott 1
Participant
@garryscott1
Thread cutting help
18 May 2019 at 12:21 #409760
Hopper
Participant
@hopper
I can't offer any advice on the Harrison but if all else fails you could get yourself a copy of Martin Cleeve's book "Screwcutting in the Lathe" and calculate what gears you need from first principals. He does have charts included to cut metric threads on an imperial lathe that could be adapted to suit the Harrison.
18 May 2019 at 13:44 #409766
Alan Waddington 2
Participant
@alanwaddington2
Assuming it has a norton gearbox fitted (some L5’s don’t) You need a 127 tooth wheel to cut metric threads

Edited By Alan Waddington 2 on 18/05/2019 13:45:54
18 May 2019 at 13:48 #409768
Clive Foster
Participant
@clivefoster55965
Gary

I assume you have the standard L5 with three speed feed box rather than the full screwcutting version. If so the charts shown here :- **LINK**

are probably correct. Not sure what computer software and printing capabilities you have but it should be possible to work up your own without unreasonable effort. I find laminating ordinary printouts in the usual plastic pouches gives an adequately durable data panel. Replicating if it does get damaged is simple so long as you remeber to save the original. I have a cheap laminator from LiDL which does such jobs just fine.

Cant find a nice download picture of the metric conversion data but I do have a copy of the table from the manual. PM me if you'd like a basic copy.

Clive
12 June 2019 at 16:44 #413912
Nigel Graham 2
Participant
@nigelgraham2
I own one of these, and bought the photocopied version of the Operator's Manual from lathes.co

Apart from anything else it will mean you are less likely to be caught out by that small gearbox on the headstock. (Yes, I have been…)

Norton Gearbox or not, and mine doesn't have one, you will still need a 127T wheel for cutting metric threads, but you may also have to reverse the lathe to wind the saddle back still in gear for each pass. I am not sure if you can use the lead-screw reverse gear to avoid running the spindle backwards – I think that would lose the correct meshing.

BEWARE though if you do run the lathe backwards under power and it has the same screwed spindle as on my lathe, you do risk the chuck unscrewing itself from the nose.

You might get away with a 63T wheel instead of 127, but it introduces a small pitch error and is best used only over short threads.
12 June 2019 at 16:49 #413914
Nigel Graham 2
Participant
@nigelgraham2
Just re-read the OP, suggesting this lathe has come without change-wheels.

If so try G & M Tools, or Home & Workshop Machinery, for a start, for replacements as well as that 127T wheel.

Also for a thread dial-indicator if that's missing.
Author

Posts