Reading glasses – frosted area

Advert

Reading glasses – frosted area

Home Forums General Questions Reading glasses – frosted area

  • This topic has 13 replies, 13 voices, and was last updated 4 May 2021 at 15:40 by Fowlers Fury.
Viewing 14 posts - 1 through 14 (of 14 total)
  • Author
    Posts
  • #543063
    Alan Jackson
    Participant
      @alanjackson47790

      Much as I try to be careful, I seem to have created a small frosted zone, on my prescription reading glasses, right in my line of sight. I was thinking of polishing the frosted zone away. My question is what should I use to avoid making them worse by frosting the whole lens. I realise it is probably better to just renew the glasses, but it seems a waste to throw them away.

      Alan

      Edited By Alan Jackson on 04/05/2021 10:40:33

      Advert
      #28141
      Alan Jackson
      Participant
        @alanjackson47790
        #543065
        mechman48
        Participant
          @mechman48

          I would try jewellers rouge; but preferably get new glasses you can't afford to mess about with your eyesight especially for the likes of we modellers where we need the best we can have. I have just bought 2 new pair of varifocals as my recent eye test showed a deterioration & the need for new lenses; not cheap!

          George.

          #543067
          Dalboy
          Participant
            @dalboy

            Many glasses use a plastic material similar to perspex. If you have a dremel type tool and a small buffing mop try that with a little t cut or Autosol (try it on perpex first) do not hold it on to long or press to hard you do not want too much heat build up.

            There is also micro mesh which you can sand down to 12,000grit and you end up with a polished shine best used with soapy water see this pen I did with them

             

            dscf5276-001.jpg

            Edited By Derek Lane on 04/05/2021 11:01:09

            #543069
            ega
            Participant
              @ega

              What about the coating, if any?

              #543070
              Nigel Graham 2
              Participant
                @nigelgraham2

                Autosol , as I remember, is quite harsh.

                There are special polishing compounds available for these classes of plastics, but as you say, test / practice on a scrap of similar plastic first.

                #543071
                Thor 🇳🇴
                Participant
                  @thor

                  Hi Alan,

                  Sorry to hear about the frosted zone on your glasses. Do you know if the material used is optical glass or some kind of plastic with a hard coating? The lenses in my glasses are made from some kind of plastic material with a thin hard coating on the surface. I would first try polishing on a part of the lens that is little used to see what happens.

                  Thor

                  #543074
                  Russell Eberhardt
                  Participant
                    @russelleberhardt48058

                    If they are glass, use jeweler's rouge. If Acrylic use Perspex polish but note it's not suitable for polycarbonate.

                    Russell

                    #543078
                    pgk pgk
                    Participant
                      @pgkpgk17461

                      Not saying it's the cause here but I;ve been guilty in the past for putting specs down on their lenses as th casue for such damage. It depends how old they are/when you last had an eye check as to whether still appropriate prescription.
                      Another option may be to fit cheapo flip up clip on mag lenses to a non-redaing pair as a conversion.

                      Also worth considering when having an eye test making sure you have a copy prescription and ordering a second pair (perhaps on-line cheapos) for use in dirty environments such as the shed…

                      pgk

                      #543080
                      Georgineer
                      Participant
                        @georgineer
                        Posted by Derek Lane on 04/05/2021 10:54:01:

                        Many glasses use a plastic material similar to perspex. If you have a dremel type tool and a small buffing mop try that with a little t cut or Autosol (try it on perpex first) do not hold it on to long or press to hard you do not want too much heat build up.

                        There is also micro mesh which you can sand down to 12,000grit and you end up with a polished shine best used with soapy water see this pen I did with them

                        Brasso is finer than T-cut and would give a better finish, but all these seem a bit harsh for something which requires an optical finish. My optician warned me against using something as apparently harmless as paper tissues for wiping glass lenses because the fibres in them can scratch the surface.

                        On the other hand, since it appears the glasses are currently not serviceable, there's not much to lose in trying.

                        George B.

                        #543081
                        Sandgrounder
                        Participant
                          @sandgrounder

                          Be careful not to take off too much and change the optical properties, I had a tiny scratch on the car windscreen which I had professionally polished out, it looked excellent afterwards but when a cars image filled the polished area it looked all distorted, I had to replace the screen.

                          John

                          #543093
                          Clive Hartland
                          Participant
                            @clivehartland94829

                            You could have raised or lowered the seat!

                            #543101
                            Clive Brown 1
                            Participant
                              @clivebrown1

                              Toothpaste will act as a fine polishing compound on plastic.

                              #543104
                              Fowlers Fury
                              Participant
                                @fowlersfury

                                You state they were prescription reading glasses. If the optician's prescription was to correct astigmatism (unlikely for reading glasses) then I would not attempt to modify the lens surface, however slightly.

                                As most of the cheapo shops sell 'self-select' reading glasses for less than a fiver (e.g. B&M, Poundland etc) – why bother?

                              Viewing 14 posts - 1 through 14 (of 14 total)
                              • Please log in to reply to this topic. Registering is free and easy using the links on the menu at the top of this page.

                              Advert

                              Latest Replies

                              Home Forums General Questions Topics

                              Viewing 25 topics - 1 through 25 (of 25 total)
                              Viewing 25 topics - 1 through 25 (of 25 total)

                              View full reply list.

                              Advert

                              Newsletter Sign-up