Welcome Terry
Depends what you want to make . I would go for a good clean second hand Myford super 7 . as you can get loads of extras for this type of machine .
Nobby

Hi Terry and welcome,

like Nobby say's, what do u want to do on it……

I had a sweet super 7 Myford with loads of gear…..but out grew it……would have another if / when I get some more room…..but don't tell er indoors……hahaha….

only room for one lathe……ended up with a nice Colchester student square head…..and I might add for a lot less money……if u go the bigger route u'll have to allow for a voltage converter in ur costings as most of the bigger ones will be 3 phase……and at about 8-10 cwt (or more) u'll need a good floor and ease of moving the thing about….

if u go the Myford route, try and get one with a cabinet …u'll never have enough room for storage….

take ur time and get one from the person who used it…… get as much tooling as can get with it, lathes are cheap but ohhhhh the tooling does cost dear….if u get lucky u'll find somebody giving up……perhaps they'll even show u how to use it…..

look out for a college course…..night school……well worth it…..

find someone near you and look at what there doing…..take ur time u only want to do this once…..the logistics of moving this stuff about is more stressful than a divorce…hahaha…..well the big'uns……

remember u can always do small stuff on a big'un but not visa versa….

keep away from the not so cheap Chinese stuff…..it'll never last…..

good luck Frank

Well and truly mugged I would say Neil, once again a beginner is given totally useless advice. He is unlikely to have the experience to know the difference between a good second hand lathe and a total piece of crap. Note: if he had this knowledge he would be unlikely to be asking for advice.

As a relative beginner myself, my advice (for what it is worth!!!!!) Is to go for a brand new lathe, minimum size 7 x 14, more practical size as bigger is usually better would be 9×20 but this will be much bigger and a lot heavier to manipulate into your workshop space, a compromise would be an 8 x 14, harder to find but are available from Amadeal amongst others.

Any of these will give you a good start and give you experience in using the lathe and learning if it is big enough to handle the work you intend to do on it. If you buy toobsmall , you can always sell it on without losing much money and buy something bigger/better. With some experience under your belt you can then take on board the advice from the glitterati re Myford and larger English made lathes.

Ignore any advice that Chinese lathes are not to be considered, there are plenty of us on here who are very happy with our Chinese lathes, as they have improved enormously over the past few years.

Good luck in you quest for a lathe, let us know what you decide on.

Regards

Howard

Welcome Terry,

Frank makes some good points about finding a secondhand lathe in general or a Myford if that is what you decide to do after hearing all the differing opinions. Just be careful you don't get seduced by shiny new paint – there are a number of refurbished? Myford machines out there, I'm sure many will be OK but buyer beware. You just have to look at at what sells on 3bay and 6umTree.

Regards

Phil

Edited By CotswoldsPhil on 07/11/2014 17:00:48

^^^^^^ What Howard said. Best advice on this thread so far.

I would like to add that if it wasn't for the influx of affordable Chinese machine tools many forums like this wouldn't exist.

You don't say want you want/need it for Terry but generally the larger the better.

I have an old and somewhat battered Super 7 but I wouldn't recommend a beginner goes for one. You can get a "bargain" but how would you know it was a good 'en? Mine was a wreck that Charles Moore decided wasn't worth his while restoring – so I've spent the past 10 years (?) or so doing the odd thing to it. It's still not as "good as new" – and most likely never will be – although I've grown fond of it and can do work good enough for my needs on it.

However, generally, I would suggest that most people acquire a lathe to actually make something on it and not to spend time fixing it up. I am probably quite odd in that respect – because I enjoy taking these things to bits and trying to get them back together again. But it's not for most people.

Decide what size of lathe you need and save your pennies for a new one – at least until you know enough to look for something "better" – and by then you may know enough to understand what "better" means to you personally (it's different for different people).

Regards,

IanT

Edited By IanT on 07/11/2014 23:01:36

Hi Terry,

Before making any decision on brand ,size , new or used there are a few things i usually sit down and have a good think about and usually make up a list of pro's and con's that i feel keep me on the straight and narrow.

How much do i wish to spend

How much space do i have to fit it in – no use buying a big heavy lathe that is 6 feet between centres if your using a space under a stair well for a workshop !

Do i want to be able to cut metric or imperial threads or both

What do i want to make with it – ie small IC engines or large traction engines this is what i use to set the parameters for Centre height and between centres dimension.

Do i really want to fiddle around fixing an old lathe and do i have the skills or knowledge to recognise or fix the problems that a used machine may have -replacing spindle bearings or regrinding the bed can be expensive on some machines.

Not knowing where you are from makes recommending suppliers difficult but if you are in the UK i would recommend you give ARC EUROTRADE a call and i'm sure Ketan will guide you along the right path if you are interested in buying new chinese made equipement.

Ian

Terry, go for a new good quality Chinese lathe, you might find it's cheaper than a Myford anyway, If you want an English lathe a Boxford would be a good start (its basicaly American, South Bend anyway).

Ian S C

1. What do you want to use it for? Watchmaking, small models, large models, making parts for vintage machinery? As has been said, you can't make big parts on a small lathe, but equally big lathes don't usually have high enough speeds for really small work and will be a bit insensitive.

2. Tell us where you are located – there may be a forum member just down the road who can help.

3. Don't rush.

Russell;

I recently had the chance to buy a Denford Viceroy for £150.

Mine is the basic model but a very good for the money.

Seen a few of these on ebay for low money.

I find these lathes are often over looked, hence can be got for a bargain.

Just note these are about 400kgs.