car boot tragedy

This topic has 10 replies, 8 voices, and was last updated 12 June 2016 at 08:12 by Paul Barter.

Viewing 11 posts - 1 through 11 (of 11 total)

Author

Posts
11 June 2016 at 19:47 #242381
Paul Barter
Participant
@paulbarter66156
Hello all, I thought I had a stroke of luck at a car boot near me, found a nice clean, unrusted Dormer adjustable reamer. However when I got it home I found a chip on one of the blades. My question is, are spare blades available?or is a chip on only one of the bladesof no consequence?Thanks to anyone who responds.

Paul

Edited By Paul Barter on 11/06/2016 19:51:27
Advert

11 June 2016 at 19:47 #18119
Paul Barter
Participant
@paulbarter66156
reamer blades
11 June 2016 at 21:06 #242385
roy entwistle
Participant
@royentwistle24699
Try it and see
11 June 2016 at 21:14 #242387
MW
Participant
@mw27036
Roy is right, you could try it on a scrapper and see what happens, if your lucky the chip will not matter if it only means it doesnt make full contact on part of the material. If the chip is on the start of the taper it might make it harder to cut to begin with.

Michael W

Edited By Michael Walters on 11/06/2016 21:16:07
11 June 2016 at 21:16 #242388
Paul Barter
Participant
@paulbarter66156
Hello Roy

Thanks for responding, I am a bit concerned that the chip will produce a ridge which may not be removed by the other blades.I will try it on a trial bore.As a new,albeit not Dormer, djustable reamer seems to be available for £15 or so I wondered if replacement blades were available, along the lines of those fitted to portable electric planers
11 June 2016 at 21:19 #242390
Vic
Participant
@vic
I would have thought it a good idea to round off the sharp corners of the chip first to prevent possible scoring.
11 June 2016 at 21:30 #242394
Tony Pratt 1
Participant
@tonypratt1
I can't see that a chip on one blade will be a problem, I doubt if spare blades are available but I stand to be corrected.

Tony
11 June 2016 at 21:39 #242396
Neil Wyatt
Moderator
@neilwyatt
If its along one edge rather than near the end, you should be OK. Might be worth stoning teh chipped area in case it has a raised burr.

Neil
11 June 2016 at 21:48 #242397
Bob Stevenson
Participant
@bobstevenson13909
…Back when I was a very poor young man I made a couple of blades for some old adjustable reeamers….still got them somewhere… I used some 'ground steel stock' , what they now call 'gauge plate' in the right thickness and after careful hardening in the forge on a shovel and tempering in the ash they worked fine……..If I recall, I made the head stock for a amall lathe with them.

Edited By Bob Stevenson on 11/06/2016 21:57:00

Edited By Bob Stevenson on 11/06/2016 21:57:19
12 June 2016 at 07:08 #242411
Speedy Builder5
Participant
@speedybuilder5
I don't think I would worry too much, I have some reamers that only have cutting flutes on about 240degrees of the circumference – they cut OK.
BobH
12 June 2016 at 08:12 #242414
Paul Barter
Participant
@paulbarter66156
Thank you all for your enlightening comments.I continue to be grateful for the generosity of the members of this site and the breadth of knowledge that is so willingly passed on. Thanks again to all of you.

Paul
Author

Posts