Myford oiler

This topic has 4 replies, 3 voices, and was last updated 29 November 2018 at 17:36 by clogs.

Viewing 5 posts - 1 through 5 (of 5 total)

Author

Posts
29 November 2018 at 16:26 #382924
David Bothwell 1
Participant
@davidbothwell1
My two oilers on my ML7 do not work properly, I have tried to adjust the top screws but the oil either runs out too quicly or not at all, any suggestions most gratefully accepted
Advert

29 November 2018 at 16:26 #26315
David Bothwell 1
Participant
@davidbothwell1
Myford oilers not working
29 November 2018 at 17:06 #382933
Jon Lawes
Participant
@jonlawes51698
There are a couple of different types, do you mean the type with a toggle on the top to start and stop the flow?
29 November 2018 at 17:11 #382937
David Bothwell 1
Participant
@davidbothwell1
Hi thanks for the reply, the top has a "knurled" top adjusting screw, is that alright?
29 November 2018 at 17:36 #382940
clogs
Participant
@clogs
they often full of gunk, strip and clean [provided the taper isn't damaged…..

.ultra fine lapping paste will sort that out…

I prefer the flip top toggle sort but they are quite expensive now…….
Author

Posts

Viewing 5 posts - 1 through 5 (of 5 total)

Please log in to reply to this topic. Registering is free and easy using the links on the menu at the top of this page.

Advert

Latest Replies

Viewing 25 topics - 1 through 25 (of 25 total)

- Topic
- Voices
- Posts
- Last Post
- My week this week! My workshop videos 1 2 … 13 14
  Started by: Phil Whitley in: The Tea Room
- 16
- 327
- 15 August 2026 at 16:02
  Phil Whitley
- When is a threaded insert preferable to tapping directly into aluminum?
  Started by: elowen01 in: General Questions
- 15
- 18
- 15 August 2026 at 13:40
  Neil A
- ELLIE the steam tram book – wanted
  Started by: apprentice in: Help and Assistance! (Offered or Wanted)
- 4
- 5
- 15 August 2026 at 13:38
  apprentice
- Alibre Atom
  Started by: Barry Smith 4 in: CAD – Technical drawing & design
- 4
- 5
- 15 August 2026 at 13:07
  Barry Smith 4
- Lidl Parkside drill bit sharpener
  Started by: AJW in: Workshop Tools and Tooling
- 14
- 22
- 15 August 2026 at 11:56
  Michael Gilligan
- How to best display a vintage 8mm cine camera
  Started by: Greensands in: Help and Assistance! (Offered or Wanted)
- 4
- 4
- 15 August 2026 at 11:45
  John Haine
- Parting off
  Started by: Peter Simpson 3 in: Beginners questions
- 13
- 21
- 15 August 2026 at 10:12
  JasonB
- How much has AI affected you personally so far? 1 2
  Started by: Robin Graham in: The Tea Room
- 22
- 31
- 14 August 2026 at 23:06
  duncan webster 1
- Tools you hate using or just don’t get on with? 1 2 3
  Started by: Hollowpoint in: General Questions
- 31
- 67
- 14 August 2026 at 19:17
  Bill Phinn
- Grayson lathe parts
  Started by: Nev Whitehurst in: Help and Assistance! (Offered or Wanted)
- 9
- 15
- 14 August 2026 at 16:55
  JasonB
- VFD Recommendations
  Started by: Keith Charters in: Electronics in the Workshop
- 9
- 11
- 14 August 2026 at 16:50
  Clive Foster
- Ball end cutters
  Started by: Speedy Builder5 in: Workshop Tools and Tooling
- 2
- 3
- 14 August 2026 at 11:21
  Speedy Builder5
- Introduction
  Started by: 254mark in: Introduce Yourself – New members start here!
- 6
- 7
- 13 August 2026 at 19:26
  Howard Lewis
- Bridge collapse
  Started by: JA in: The Tea Room
- 3
- 3
- 13 August 2026 at 18:09
  JasonB
- Solar eclipse
  Started by: JA in: The Tea Room
- 5
- 5
- 13 August 2026 at 17:47
  Gerard O’Toole
- New Member, Piano Restorer
  Started by: henrypianoman in: Introduce Yourself – New members start here!
- 10
- 17
- 13 August 2026 at 13:14
  John Haine
- Self dimming welding mask
  Started by: Andrew Tinsley in: General Questions
- 11
- 14
- 13 August 2026 at 12:02
  noel shelley
- 3/4″ steel conduit pipe?
  Started by: Andrew Tinsley in: Materials
- 7
- 12
- 13 August 2026 at 06:50
  JasonB
- Problem firing up
  Started by: Michael Callaghan in: General Questions
- 10
- 15
- 12 August 2026 at 17:15
  Chris Gunn
- Bridgeport Series 1 CNC 1 2 3 4
  Started by: tomcnc in: CNC machines, Home builds, Conversions, ELS, automation, software, etc tools
- 12
- 80
- 12 August 2026 at 10:13
  seemack
- Annoying Ad 1 2
  Started by: jaCK Hobson in: Website Questions, Comments, and Suggestions
- 13
- 28
- 12 August 2026 at 07:38
  JasonB
- A chemistry question
  Started by: duncan webster 1 in: The Tea Room
- 10
- 14
- 11 August 2026 at 13:29
  Juddy
- Solar panel
  Started by: duncan webster 1 in: Electronics in the Workshop
- 12
- 21
- 10 August 2026 at 22:29
  John Haine
- Lightning 1 2 3
  Started by: duncan webster 1 in: Electronics in the Workshop
- 17
- 67
- 10 August 2026 at 17:39
  duncan webster 1
- can anyone make me a file? 3d file
  Started by: Ian Parkin in: 3D Printers and 3D Printing
- 8
- 11
- 10 August 2026 at 16:21
  Roderick Jenkins

Myford oiler

Myford oiler

Latest Replies

Latest Issue

August 2026

Newsletter Sign-up

Latest Replies