Beginners questions

Beginners questions

This forum has 7,329 topics, 113,503 replies, and was last updated 16 September 2026 at 08:56 by roy entwistle.

Viewing 25 topics - 3,926 through 3,950 (of 7,329 total)

← 1 2 3 … 157 158 159 … 292 293 294 →

- Topic
- Voices
- Posts
- Last Post
- Are brake hone grit sizes graded differently to sandpaper ?
  Started by: Brian John
- 7
- 13
- 16 July 2016 at 18:20
  Michael Gilligan
- three phase motor current
  Started by: Paul Barter
- 10
- 18
- 15 July 2016 at 23:50
  John Olsen
- Will some sort of glue be good enough for this…
  Started by: Robin Graham
- 15
- 25
- 13 July 2016 at 10:42
  KWIL
- Lathe help!!
  Started by: Andrew Simpson 6
- 14
- 25
- 12 July 2016 at 22:47
  Andrew Simpson 6
- How do I make a steam operated valve?
  Started by: nigel jones 5
- 12
- 22
- 12 July 2016 at 21:43
  julian atkins
- drill sets 1 2 3
  Started by: ron grimshaw
- 37
- 63
- 12 July 2016 at 21:15
  bodge
- What is the brown colouring on the hand reamers ?
  Started by: Brian John
- 7
- 9
- 11 July 2016 at 19:50
  Neil Wyatt
- Threading feed table & calculators, do not match. 1 2
  Started by: Dave Smith the 16th
- 14
- 41
- 11 July 2016 at 19:30
  Dave Smith the 16th
- What does this control do ?
  Started by: Brian John
- 11
- 20
- 11 July 2016 at 17:23
  Michael Gilligan
- Stuart 10v Cylinder honing?
  Started by: Martin King 2
- 5
- 14
- 11 July 2016 at 11:34
  mechman48
- 4″ independent lathe chuck recommendations and holding capacity 1 2
  Started by: carl too too
- 9
- 31
- 10 July 2016 at 10:09
  bodge
- oil 1 2
  Started by: Allen Paddock
- 22
- 42
- 8 July 2016 at 09:00
  Jon Gibbs
- Drummond M First Time Use Troubles! 1 2
  Started by: James Jenkins 1
- 15
- 38
- 7 July 2016 at 12:15
  Martin Newbold
- keyway on involute cutter
  Started by: Dave Smith the 16th
- 9
- 14
- 7 July 2016 at 08:30
  not done it yet
- Carbide tips
  Started by: Graham Lewis 1
- 5
- 8
- 6 July 2016 at 14:00
  Split Pin
- Air/Gas compression in a Steam Engine.
  Started by: Ed Duffner
- 2
- 4
- 5 July 2016 at 17:08
  Ed Duffner
- Tools for turning in the mill
  Started by: Tom Davies
- 4
- 7
- 4 July 2016 at 09:02
  JasonB
- best lathe tool for cast iron
  Started by: David lawrence 3
- 6
- 8
- 4 July 2016 at 08:11
  David lawrence 3
- adjustable (QCTP) tool post 1 2
  Started by: Martin Newbold
- 13
- 29
- 4 July 2016 at 00:18
  Bazyle
- Mini Lathe Fuse
  Started by: Brian G
- 6
- 10
- 1 July 2016 at 22:18
  Neil Wyatt
- air brush or rattle cans
  Started by: Mike Bondarczuk
- 4
- 6
- 1 July 2016 at 10:47
  Mike Bondarczuk
- which parting tool for small lathe
  Started by: Martin Newbold
- 15
- 25
- 30 June 2016 at 23:00
  Howard Lewis
- Parting with power cross feed
  Started by: Robin Graham
- 7
- 10
- 30 June 2016 at 22:24
  MW
- Coolant system.
  Started by: Mark Eisen
- 8
- 11
- 30 June 2016 at 15:47
  Jon
- Is their a relationship between boiler volume, pressure and cylinder volume?
  Started by: Simon Robinson 4
- 5
- 6
- 29 June 2016 at 21:04
  julian atkins

Viewing 25 topics - 3,926 through 3,950 (of 7,329 total)

← 1 2 3 … 157 158 159 … 292 293 294 →

You must be logged in to create new topics.

Latest Issue

October 2026

Buy Latest/Back Issues

Newsletter Sign-up