Good source of gear to make threading attachment for lathe

Advert

New Replies

Report Bug

Help/FAQs

Good source of gear to make threading attachment for lathe

This topic has 9 replies, 7 voices, and was last updated 27 March 2018 at 22:43 by Jim Nic.

Viewing 10 posts - 1 through 10 (of 10 total)

Author

Posts
26 March 2018 at 16:15 #347669
John Aitken
Participant
@johnaitken84086
I have an Emco Unimat 3 lathe that I’m trying to make a screw threading attachment for. Specifically for ever four turns the work piece does I want the lead screw to do one turn. 4 threads per mm.

To do this I’d like a scours of high quality gears with a wide range of teeth numbers so can anyone recommend a good source?

Thank you
Advert

26 March 2018 at 16:15 #29805
John Aitken
Participant
@johnaitken84086
26 March 2018 at 18:38 #347680
Michael Cox 1
Participant
@michaelcox1
Try here:

https://www.technobotsonline.com/

I have sourced gears/ timing belt pulleys etc from this company. Fast efficient service and good prices.

Just a satisfied customer.

Mike
26 March 2018 at 18:56 #347681
Bazyle
Participant
@bazyle
Get a set of gears for a mini lathe from one of the usual lathe suppliers. That way they will have the right range and values.
26 March 2018 at 20:30 #347689
Jim Nic
Participant
@jimnic
I'll be interested to see how you arrange the gears to drive your leadscrew on a Unimat 3.

The U3 I have has no mechanical connection between headstock mandrel and leadscrew. The only drive I have seen is a mechanism which connects to the end of the leadscrew and takes it's drive via a rubber belt off the motor pulley as a means of feeding the crosslide, but that has a fixed ratio.

Jim
27 March 2018 at 04:53 #347708
Thor 🇳🇴
Participant
@thor
Posted by Jim Nic on 26/03/2018 20:30:56:

I'll be interested to see how you arrange the gears to drive your leadscrew on a Unimat 3.

……

Jim

May be something like this or this? The Taig is a bit different from the Unimat 3 of course.

Thor

Edited By Thor on 27/03/2018 04:55:47
27 March 2018 at 09:07 #347724
Mark Rand
Participant
@markrand96270
To answer Chris's original question. HPC gears are good quality and have a wide range.

Edited By Mark Rand on 27/03/2018 09:07:44
27 March 2018 at 12:20 #347750
Cornish Jack
Participant
@cornishjack
I have 3 Unimats (don't ask!) one of which is set up solely for screw cutting with about 20 or so threading sets. It is a very good system in use and I think some sort of 'home-brew' copy would be preferable to a method relying on lead screw drive. The Unimat system does ensure exact repeatability.

rgds

Bill
27 March 2018 at 14:30 #347769
John Aitken
Participant
@johnaitken84086
Posted by Mark Rand on 27/03/2018 09:07:27:

To answer Chris's original question. HPC gears are good quality and have a wide range.

Edited By Mark Rand on 27/03/2018 09:07:44

Thank. They seem to have a good suply of all the teeth numbers I could ever want. I'll go with them.

I’m not buying the original Unimat attachment because it is out of stock everywhere and it doesn’t do the threading I need. If I make my own I will have a larger selection of thread I can make, it will be cheaper and I will have gained some skill I would not otherwise of had.
27 March 2018 at 22:43 #347821
Jim Nic
Participant
@jimnic
Good for you Chris. As I said, I would be interested to see how you do it (and I wasn;'t being facetious) so I hope you can enlighten us when you have completed it, perhaps by updating this thread.

Jim
Author

Posts