Manual machine tools

Manual machine tools

This forum has 3,570 topics, 50,924 replies, and was last updated 16 August 2025 at 07:45 by Diogenes.

Viewing 25 topics - 2,076 through 2,100 (of 3,570 total)

← 1 2 3 … 83 84 85 … 141 142 143 →

- Topic
- Voices
- Posts
- Last Post
- Glass-scales-ZX45-RF45 clone
  Started by: Neil Lickfold
- 6
- 15
- 6 May 2018 at 20:52
  Neil Lickfold
- Myford super 7 long bed stiffness
  Started by: PutneyChap
- 3
- 5
- 4 May 2018 at 10:15
  PutneyChap
- Recently Acquired Drummond B lathe
  Started by: Don Hutton
- 8
- 10
- 4 May 2018 at 01:04
  bricky
- WM14 Mill Drill lubrication
  Started by: michael howarth 1
- 4
- 5
- 3 May 2018 at 20:56
  Another JohnS
- Drummond Shaper Feed
  Started by: not done it yet
- 7
- 13
- 3 May 2018 at 19:45
  Martin Newbold
- Rotary table 1 2 3
  Started by: Richard Clark 1
- 16
- 53
- 1 May 2018 at 23:07
  Michael Gilligan
- Myford toolpost stud
  Started by: John Haine
- 5
- 11
- 1 May 2018 at 13:42
  Michael Gilligan
- Dismantling English Electric 1/2 hp motor
  Started by: Mike Crossfield
- 4
- 6
- 30 April 2018 at 20:45
  Mike Crossfield
- Spindle repair – removing broken bearings
  Started by: babiels
- 6
- 11
- 30 April 2018 at 16:47
  mark costello 1
- Bridgeport Mill – Convert to 240v Single Phase
  Started by: mtrehy mtrehy
- 16
- 25
- 28 April 2018 at 22:26
  Muzzer
- add oil grooves for bedways
  Started by: Neil Lickfold
- 2
- 5
- 28 April 2018 at 09:12
  Douglas Johnston
- Zeatz dividing head
  Started by: Matt Andrews
- 3
- 8
- 25 April 2018 at 05:26
  Thor 🇳🇴
- Denham Junior lathe.. Gears replaced and running again
  Started by: Brian Fosh 1
- 2
- 6
- 24 April 2018 at 18:43
  Brian Fosh 1
- Alexander 3A 3D machine
  Started by: Brian H
- 7
- 20
- 20 April 2018 at 18:06
  Bill Phinn
- Colchester master 1.5 levelling
  Started by: Bramhp
- 2
- 3
- 19 April 2018 at 20:43
  David George 1
- Where to get a running bearing for Ajax AJ8 mill
  Started by: Mark Davison 1
- 6
- 11
- 18 April 2018 at 14:28
  geoff adams
- old myfords
  Started by: lee sargent 1
- 6
- 9
- 17 April 2018 at 03:01
  Hopper
- Another mystery lathe identification thread
  Started by: Rainbows
- 10
- 17
- 16 April 2018 at 18:46
  Andrew Entwistle
- Rexon RDM 500 mill drill spindle nose piece – is it screwed on?
  Started by: Andrew Hutchinson
- 1
- 2
- 14 April 2018 at 04:36
  Andrew Hutchinson
- Treadle polisher/ grinder for sale, swap or part ex
  Started by: James Wilkinson 3
- 3
- 6
- 13 April 2018 at 07:49
  JasonB
- drill / mill table load
  Started by: nigel dale
- 8
- 11
- 12 April 2018 at 20:41
  nigel dale
- Bridgeport Turret Mill series 1 X axis power feed
  Started by: Nick Boyland
- 4
- 5
- 12 April 2018 at 14:36
  john fletcher 1
- ML10 topslide – is it compatible with ML7 or Super 7
  Started by: PutneyChap
- 3
- 5
- 12 April 2018 at 12:24
  John Haine
- Chinese End Mill Sharpener
  Started by: peak4
- 6
- 11
- 7 April 2018 at 21:52
  peak4
- Schaublin 13
  Started by: Clive Hartland
- 7
- 9
- 5 April 2018 at 17:14
  larry Phelan

Viewing 25 topics - 2,076 through 2,100 (of 3,570 total)

← 1 2 3 … 83 84 85 … 141 142 143 →

You must be logged in to create new topics.

Latest Issue

September 2025

Buy Latest/Back Issues

Newsletter Sign-up