By continuing to use this site, you agree to our use of cookies. Find out more
Forum sponsored by:
Forum sponsored by Allendale Jan 24th

Junior hacksaw blades

All Topics | Latest Posts

Search for:  in Thread Title in  
AJW05/03/2021 21:17:20
avatar
337 forum posts
130 photos

For sawing most metals I use a 12 inch hacksaw fitted with usually a 24 you blade. I've cut loads with the current blade including lots of 2 inch bar - the blades been in the saw for months.

I also at times use a junior hacksaw fitted with an eclipse blade and am always disappointed at how long it lasts.

Can anybody recommend a make that will last better?

Alan

Alain Foote05/03/2021 21:33:48
51 forum posts
6 photos

I think you will find that junior hacksaw blades are not high speed steel like the better quality normal hacksaw blades generally are.

John Haine05/03/2021 21:59:44
3784 forum posts
220 photos

I only recently discovered that Junior Hacksaws work much better if you turn the blade round and cut on the pull stroke. I found some Bahco blades that seem much better.

Clive Foster05/03/2021 22:22:30
2637 forum posts
92 photos

They work much better in a proper frame iwth screw tensioner than in the cheap bent steel rod device.

The are softer than the usual hacksaw blade. Bimetallic is impossible and a hard one would snap in nothing flat.

Itty bitty teeny weeny teeth too so clogging is an issue. Being so small and light the tendency is to push down and force the saw.

Most folk tend to go too fast. Apparently the proper speed is something under half normal hacksawing speed which feels really slow.

Clive

John Haine05/03/2021 22:33:21
3784 forum posts
220 photos

The flimsy frame is much less of an issue if you cut on the pull stroke.

AJW05/03/2021 22:56:12
avatar
337 forum posts
130 photos

Thanks guys, I do try and take it steady when sawing although I didn't realise Bahco made saw blades, I've always been impressed with their spanners so will have a search for saw blades.

Alan

Bazyle05/03/2021 23:55:58
avatar
5834 forum posts
217 photos

Has the quality degraded over time, or more recently? I have always considered them to be much harder than regular hacksaws but hence less durable long term. As well as small cutting jjobs and accessibility I choose them for all harder materials like silver steel and piano wire to save my full size blades for the bigger bits of soft mild steel.

AdrianR06/03/2021 07:54:19
499 forum posts
35 photos

I too have found junior hacksaw blades to be soft recently, but I put it down to buying DIY store blades.

A blade I have had for at least 30 years and probably came from R.S. still cuts even if a little dull. The DIY store ones are lucky to survive the first pass of the blade. I have bought Eclipse blades and they are better, still not as good as I remember them to be.

But how much of that is a rosy memory of days gone past?

Steve Neighbour06/03/2021 08:10:08
102 forum posts
1 photos

The makes that perform well are Bahco or Hilka, and avoid using the cheap wire type frames, try and use one with a tension screw yes

AJW06/03/2021 09:20:46
avatar
337 forum posts
130 photos

Perhaps I'm expecting too much? The blades I have are all old stock and are probably 30+ years old so pre date the cheap influx of 'pound shop' type product.

Having had a bit of a search and hoping to find something like the bimetal larger blades where we have a hss cutting edge but all I could find was hardened and tempered carbon steel so have gone for a pack of bahco ones and will see how they go!

Alan

John Haine06/03/2021 09:45:33
3784 forum posts
220 photos

Try reversing the blade when you do (or does everyone do that anyway it's just me that didn't realise?).

roy entwistle06/03/2021 10:24:33
1337 forum posts

I have always used junior hacksaws on the pull. Same as piercing saws and fretsaws

Roy

Nigel McBurney 106/03/2021 11:25:18
avatar
845 forum posts
3 photos

my first genuine eclipse junior hack saw frame ,new in 1958 and still has my clock number stamped on it,seems to have more spring in it than later ones from unknown sources,and holds the blade tight,still works ok ,I have always cut in the push direction,never tried to pull.The quickest way to ruin a blade is to cut "unbrako" socket screws. In more recent times i tend to cut toughened bolts and socket screws with a 1 mm disc in an angle grinder,then this yearI purchased a Dewalt cordless angle grinder and that tool is useful saves the need for long cables when using it around the sheds and yard.

Brian Wood06/03/2021 17:56:55
2380 forum posts
37 photos

Thank you gentlemen for suggesting the blade works better on the pull stroke, I now agree after trying it out

Regards Brian

Grizzly bear06/03/2021 18:41:18
278 forum posts
8 photos

While on the subject of junior hacksaws, they make very good pruning saws.

Use a woodworking bandsaw blade, cut to length and drilled for small self tappers.

Used on the pull, watch your fingers.

Bear..

Georgineer06/03/2021 20:05:29
503 forum posts
30 photos
Posted by Clive Foster on 05/03/2021 22:22:30:

They work much better in a proper frame iwth screw tensioner than in the cheap bent steel rod device.

...

I use a cheap bent steel rod device, which was the first thing I made when I started my apprenticeship in 1969. I'm planning to replace it when it wears out.

George B.

roy entwistle06/03/2021 21:35:04
1337 forum posts

Bear you can get junior hacksaw blades for wood

Roy

Brian Morehen07/03/2021 08:40:58
avatar
146 forum posts
11 photos

I always smear Both types of hacksaw blades with some lathe cutting oil makes life so much more easier also st ops clogging and seems to make the blades last longer . give it try.

Regards to all Bee M

Grizzly bear07/03/2021 22:09:48
278 forum posts
8 photos

Roy,

Make the blades from broken bandsaw blades.

I doubt there are any wood blades, they wouldn't be accurate enough.

Having said that:

Irwin 14tpi Wood Junior Hacksaw Blades 6" (150mm) 10 Pack | Hand Saw Blades | Screwfix.com

Bear..

Mike Poole07/03/2021 22:38:05
avatar
Moderator
2940 forum posts
70 photos
Posted by AJW on 05/03/2021 22:56:12:

Thanks guys, I do try and take it steady when sawing although I didn't realise Bahco made saw blades, I've always been impressed with their spanners so will have a search for saw blades.

Alan

Sandvik may be a name more associated with saw blades and they bought Bahco 30 odd years ago. As usual brand names get used and abused when they get hoovered up into a conglomerate so Bahco who invented the crescent adjustable have their name applied to saw blades. I think Snap On own them now so who knows what names will turn up on anything now.

Mike

All Topics | Latest Posts

Please login to post a reply.

Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Latest Forum Posts
Support Our Partners
ChesterUK
JD Metals
Eccentric July 5 2018
Warco
cowells
emcomachinetools
Eccentric Engineering
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest