By continuing to use this site, you agree to our use of cookies. Find out more
Forum sponsored by:
Forum sponsored by Allendale Jan 24th

Are these Flexispeed accessories?

All Topics | Latest Posts

Search for:  in Thread Title in  
Adrian R211/08/2020 11:38:57
33 forum posts
5 photos

Can anyone tell me if the items below are accessories for this Flexispeed, or if they have just been put in the same box because they are painted a similar hammered blue.

A is an angle bracket, but doesn't seem to fit anywhere on the lathe.

B might be a riser, it is the same width as saddle; doesn't appear to fit tailstock.

Bolt holes on vice C are on same centres as A but different diameters.

Thanks in advance for any help.

(p.s. I do have the lathe cross slide but it was removed in this photo)

img_3265.jpg

img_3266.jpg

Neil A11/08/2020 17:26:52
64 forum posts

The angle plate (A) and the small machine vice (C) look to be the same as the ones I got for my Flexispeed from the Norfolk Lathe & Tool Co when they were being made in North Walsham. The angle plate is a bit crudely made but the vice was machined all over.

I don't know what the block (B) is, as you say, from the paint it is associated with the lathe. Judging from size and the single hole it could fit on top of the compound slide instead of the tool holder. But what you would use it for I don't know, maybe as a pivot for a hand held tool?

Item (D) could be homemade clamps for the face plate, but I'm guessing there. Item (E) I have not a clue!

I hope someone else with a Flexspeed can provide some more answers.

Neil

Adrian R212/08/2020 10:19:18
33 forum posts
5 photos

Thanks for the reply Neil - do (A) and (C) give some vertical slide capability? If so where do you mount them?

(B) pivot for a hand held tool, interesting idea, I wonder what the tool holder would have looked like. Re-examining the bits again last night I noticed that the small hole has a spring inside it - some sort of pin or ball detent?

Adrian

Neil A12/08/2020 22:09:12
64 forum posts

I'm afraid my memory is a little bit hazy on how exactly I arranged the angle plate and vice, it's been over 40 years since I last used then. They got put away when I acquired other tooling. The lathe still gets used on the odd occasion just to make sure it still works, but just for very simple turning jobs now.

I think that I bolted the angle plate directly to the cross slide tee slot and then the vice to the angle plate. This would have given very limited and not very accurate vertical adjustment. I cannot remember if I managed to arrange any fine vertical adjustment, if I did it was probably some lash up using the compound slide as I had nothing else in those days.

The block (B) is still a bit of a puzzle to me, I can only speculate on its use now that you say there could be a locating detent in the face.

I'm sorry not to be more helpful, I just wish that I could remember more clearly just how I did.

Neil

Adrian R213/08/2020 09:01:23
33 forum posts
5 photos

Thanks, it's useful at least to know that these are intended for use with the lathe. I've found a picture now that also shows the lathe with the angle bracket and a fully machined vice as you describe. It also had a proper vertical slide but looks like that was an option. I hadn't thought of trying to remount the cross slide, will have to look at that again.

Likewise I haven't use this for anything for a while but would still like to know what I've got.

Adrian

John Haine13/08/2020 09:25:38
3269 forum posts
175 photos

Is it missing a topslide? That may go on the angle bracket, on the crosslide, with the vice on the topslide. Similar arrangement to the Hobbymat.

Adrian R213/08/2020 10:28:21
33 forum posts
5 photos

I've got the compound/topslide, however no holes in it that will line up with the either the angle bracket or vice.

Adrian

Edited By Adrian R2 on 13/08/2020 10:56:42

All Topics | Latest Posts

Please login to post a reply.

Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Latest Forum Posts
Support Our Partners
EngineDIY
ChesterUK
Eccentric July 5 2018
cowells
emcomachinetools
Warco
Eccentric Engineering
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest