By continuing to use this site, you agree to our use of cookies. Find out more
Forum sponsored by:
Forum sponsored by Allendale July 23rd

Stuart Turner #1

All Topics | Latest Posts

Search for:  in Thread Title in  
John Purdy16/08/2019 19:31:39
avatar
172 forum posts
59 photos

    Finished my Stuart Turner #1. Bought the castings second hand in 1996, They were initially bought in the late '60s or early '70s, and when I got them they had been through 2 or 3 (or more) owners. Everything was there except the rings were broken. Finally got around to starting it on 5 Oct. last year.
    Have run it on air for around an hour to run it in and it now will run down to 12-13 psi. The rings are producing quit a bit of friction in the bore. I noticed that at the slowest speed it runs quite unevenly. After a bit of head scratching and watching it was apparent that it was slowing down over TDC the once about 30 deg beyond it would speed up down and over BDC only to slow down again approaching TDC.
    So as an experiment I removed the rings and the piston rod packing and found it turns over extremely freely (the piston has about 2-3 thou clearance in the bore).  When turned over slowly by hand and the piston gets to about 20-30 deg after TDC  it  rotates by it's own weight down to BDC, slightly beyond then back to BDC. So it would appear that the slow speed unevenness is due to the fact that there is no counterbalances on the crank to compensate for the reciprocating mass of the piston, rod, crosshead and con rod. Might look at fitting some in the manner of the ST#5 as an experiment.

Johndscn3231.jpgdscn3213a.jpgdscn3214a.jpgdscn3228.jpgdscn3227.jpg

Edited By John Purdy on 16/08/2019 19:32:52

Edited By John Purdy on 16/08/2019 19:36:11

Edited By John Purdy on 16/08/2019 19:41:39

JasonB16/08/2019 19:36:03
avatar
Moderator
16018 forum posts
1684 photos
1 articles

Very nice John, and a pleasant change from the usual greens, neat cladding too.

3404616/08/2019 19:56:52
695 forum posts
7 photos

Very neat job indeed - well done.

Prefer the colour scheme to the Stuart green

Bill

Jeff Dayman16/08/2019 20:14:51
1593 forum posts
39 photos

That's looking great John! Well done! I like the colour scheme as well.

Brian H16/08/2019 20:17:00
avatar
1191 forum posts
87 photos

Very nice John, well done,

Brian

mechman4817/08/2019 10:54:27
avatar
2432 forum posts
372 photos

Very nice John; I'm tending to go for other colours as well rather than sticking to Stuart green & black. What is the colour on your model, it looks very similar to the rattle can colour of 'FED Aero crème de la crème' I have ?

George.

Harry Wilkes17/08/2019 12:03:15
avatar
699 forum posts
59 photos

Nice job have to agree with Jason pleasent looking colour

H

John Purdy17/08/2019 17:06:04
avatar
172 forum posts
59 photos

Thanks all for the complimentary comments.

George, the colours, I mixed up from scratch as I couldn't find anything like I liked in either paint tins or spray cans from builders or auto supply shops. The brown is what I'd call a "bright chocolate" mixed up from a quite dark brown with some red added and then a little yellow to lighten it up. The cream was white with a little yellow to make a bright cream, then a drop or two of the chocolate to tone it down. It actually is a little darker that shows in the pictures, the colour balance has made it come out quite a bit whiter. There was much mixing up of drops of paint on a sheet of paper till I got what I liked ( then trying to remember what I had used!).

John

Edited By John Purdy on 17/08/2019 17:08:16

Emgee17/08/2019 17:28:11
1157 forum posts
206 photos

John

As others have commented makes a change from usual colours, everything on your engine looks crisp and well finished, congratulations.

Emgee

Mick B117/08/2019 17:42:21
1151 forum posts
63 photos
Posted by Jeff Dayman on 16/08/2019 20:14:51:

That's looking great John! Well done! I like the colour scheme as well.

+1 - nice work indeed.

I wanted a colour like that for my Stuart Beam about 20 years ago:-

stuart beam.jpg

(Matrioshka courtesy grandkids )

I used a Humbrol enamel in the end, but I don't think I've any left and don't know the code no. Your lagging is good - I might add some to mine when I do a refurb, which it's obviously beginning to need...

blush

Mark Gould 121/08/2019 17:02:44
125 forum posts
86 photos

John, that is a beautiful No. 1 and as already said a welcome change in colours. Well done, I know how much work goes into making a running No. 1 as I am experiencing myself.

All Topics | Latest Posts

Please login to post a reply.

Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Support Our Partners
Advertise With Us
Eccentric July 5 2018
Warco
Eccentric Engineering
Ausee.com.au
ChesterUK
TRANSWAVE Converters
Meridienne oct 2019
emcomachinetools
Allendale Electronics
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest