|Neil Lickfold||06/05/2018 02:27:10|
|628 forum posts|
Does anyone know where I can get the actual specs for the Dickson Quickchnage tool holders for the Myford super 7 ? I would like to know the dimensions that they use for the Vee and the area where they use a T slot cutter for the hold back clamp. I have some and can measure them, but would like to know what the actual spec is.
My holders have W stamped on the inside of where the T slot cutter has passed through.
Thanks for any replies,
Edited By JasonB on 06/05/2018 07:54:57
|Speedy Builder5||06/05/2018 07:27:50|
|2080 forum posts|
For dimensions, try this link:-
Edited By JasonB on 06/05/2018 07:55:17
18650 forum posts
I've not seen published drawings of the finer details just the overall sizes as above link. As yours have the original W mark probably OK to measure them.
Edited By JasonB on 06/05/2018 07:58:34
|Neil Lickfold||06/05/2018 12:36:01|
|628 forum posts|
Thanks Jason for making a new and better titled thread. I wonder if those who have made Dickson 00 tool holders are willing to share the dimensions that they used for making their own tool holders?
Thanks, Neil Lickfold
1011 forum posts
Neil here is a sketch I made from an original Myford/Dickson tool holder for another forum member last year, he was/is in France hence me using metric dimensions--if you want imperial either convert them or let me know.
Hope its of use to you -- John
Edited By JohnF on 06/05/2018 16:44:57
|Neil Lickfold||06/05/2018 20:38:43|
|628 forum posts|
Thanks for that John.
|Phil P||08/12/2019 12:20:51|
|641 forum posts|
Just a quick tip for those who don't know it already.
To get an accurate dimension between the "Vee's" ( the 47.98 dim in the above sketch )
Lay two bits of 1/4" diameter HSS toolsteel or something similar in each Vee, then take two measurements, one inside the round bars and another outside of them, adding the two together and dividing the result by two will give you a much more accurate dimension than trying to fit your digital verniers across the Vees.
Also, the relationship between the 47.98 and the 3.7 dimensions is very important so as to make sure the clamp works in the same range as your existing toolholders.
Sorry if I am teaching granny to suck eggs.
Here is a parting toolholder I made for my miniature Dixon style rear toolpost on the Myford, using the method described.
Here is the drawing to show what I mean.
Edited By Phil P on 08/12/2019 12:22:49
Edited By Phil P on 08/12/2019 12:38:22
|388 forum posts|
Or in the words of the classic rhyme:
Teach not thy parent's mother to extract
the embryonic juices of an egg by suction;
That worthy lady can herself the feat enact,
quite irresepective of thy kind instruction.
|duncan webster||08/12/2019 20:25:56|
2736 forum posts
Neil needs to twist Phil's arm for a MEW article here, that's a lot better than holding the KitQcut blade via 2 countersunk screws
|David George 1||08/12/2019 21:25:36|
1304 forum posts
This is my drawing of toolpost stamped with a W in slot.
Please login to post a reply.
Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!
You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.
Click THIS LINK for full contact details.
For subscription issues please see THIS LINK.