By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for Nobby

Here is a list of all the postings Nobby has made in our forums. Click on a thread name to jump to the thread.

Thread: What is this item
01/03/2018 17:54:25

Hi Michael
Thank you for link It makes sense to me Stress over Strain = E etc
Nobby

01/03/2018 17:31:18

Its still a puzzle for me . Its well made

01/03/2018 15:30:38

Thank you ASF came with a job lot of tools I bought on line

01/03/2018 15:08:09

sam_1085.jpg

Edited By Nobby on 01/03/2018 15:09:18

Edited By Nobby on 01/03/2018 15:10:35

Thread: Tail stock die holder.
27/01/2018 11:19:21

Hi Adrian
You could make one like this and add to it as you can  see you can m/c under power and set the depth when the drive peg reaches the end of the slot it just spins and you an remove it 

Nobby

Edited By Nobby on 27/01/2018 11:29:33

Thread: Sine Protractor
12/01/2018 17:42:13

Hi Michael
Yes that side plate was cut down for the original one . Well spotted . i will have to sort that out
Nobby

12/01/2018 17:42:12

Hi Michael
Yes that side plate was cut down for the original one . Well spotted . i will have to sort that out
Nobby

12/01/2018 17:39:27

Hi Howard & Stew
You are right Howard the ones in the photo I made out of H&T gauge plate to save using the the best ones .
Stew that would be a good little project as I said i find them useful . I have sine bars angle plates etc but this is good and quick
Regards Nobby

12/01/2018 09:04:21

Hi Stew
Thank you Those gauge blocks you can see i made to save using the best slips are standard sizes for 20 30 degrees etc
I hope you did'n mind me jumping in on you thread your sine protractor is brilliant
Nobby

11/01/2018 18:49:49

I used a Vice I bought  to alter into  a 5" sine vice  very useful angles

Edited By Nobby on 11/01/2018 18:55:01

Thread: Rear parting off tool
14/12/2017 11:22:55

rear partingHi Bob
I made one for my S7 it works fine here it s in action parting off

Edited By Nobby on 14/12/2017 11:24:11

Thread: What lathe are these change wheels off
01/12/2017 22:49:16

HiJan & Guys
They may be Drummond like these on mine note the hole's not keywaysgears

Thread: Boring head ball turner
30/11/2017 10:42:49

Hi Guys
Here is mine using a boring head I maderadius turning

Edited By Nobby on 30/11/2017 10:44:53

Thread: Drummond Shaper Restore
10/10/2017 22:32:55

clapper boxHi Gerry
I have a Drummond hand shaper if you need any dimensions I maybe able to help This is the original colour Nobby
drummond shaper

Thread: How could I make this curved conrod?
08/10/2017 15:24:26

Hi Raglan
Thank you for posting this photo of my method . I found works quite well
Nobby

06/10/2017 23:21:22

I would say make a template like Mike says set up similar to my effort  The template fits in to tailstock Nobby

Edited By Nobby on 06/10/2017 23:22:51

Thread: Blunt hand rea.mers
15/08/2017 17:25:30

Hi Guys
Yes Clive its called bumping up a reamer . we used ot quite often you can also put a shim say about 2 thou along side the reamer
Nobby

Thread: Return of the Shaper
07/08/2017 15:40:48

Hi Guys
I have a Drummond hand shaper . At work in the 70s there a 36" shaper I used to machine circular grooves in a mould for round components,drummond shaper

Edited By Nobby on 07/08/2017 15:41:21

Thread: Milling in a pillar drill
03/07/2017 16:16:27

HI r]Richard & Ian
The tools fly cutter boring head ect screw on with 1/2" thread 2nd picture shows me turning the location nice and true in situ I have made several cutter holders 6MM one shown in 1st picture 6 m.m cutter holdertruing 3/4 location

03/07/2017 12:50:21

no drawbarvarious cutterstry thisHi Guys Have a look at my idea to hold cuttersparts

Edited By Nobby on 03/07/2017 12:51:00

Edited By Nobby on 03/07/2017 12:52:45

Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Latest Forum Posts
Support Our Partners
ChesterUK
EngineDIY
cowells
emcomachinetools
Eccentric July 5 2018
Warco
Eccentric Engineering
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest