By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for Saxalby

Here is a list of all the postings Saxalby has made in our forums. Click on a thread name to jump to the thread.

Thread: ECLIPSE No:180 Instrument Vice info needed please
01/05/2020 12:47:57

Martin Have PM you the sketch

01/05/2020 12:47:57

Martin Have PM you the sketch

30/04/2020 16:31:13


Just measured mine.

The jaws are 1/2 inch X 29/64 inch. The top angled at 30 Deg

thread is 7/32 X 28 BSF and the plain rod 7/32 and both 1 7/8 inch long

The attachment bar is 3/8 inch milled square to 5/16 inch

Will do a sketch later if you still need it.

Regards Barry

Thread: Boxford AUD clutch
24/03/2020 22:16:44

Many moons ago ME workshop published plans for a counter shaft clutch for Myford lathes. Which is essentially what the Boxford option was. I did start to make the bits to modify the ME10 but other projects take over.


24/03/2020 16:26:14

I have both a ME10 and an AUD. Don't have a clutch on either. A clutch was available as an extra on the ME10 but not on the AUD (not listed in the original list of options that I have)

As nick sugests, motor with built in clutch, as I also nt see where one could be fitted on an AUD


Thread: Milling machine & Shaper query
28/01/2020 13:18:26

I have a Boxford shaper and a Tom Senior Mill. Use the shaper a lot for key slots in gears and pulleys etc. Also love the very fine finish that you can get on steel, almost a ground finish.

Would never part with the shaper.

Thread: Do you clean your workshop at the end of the day?
28/06/2019 11:04:15

Im withTrevor - wait until tools and turned parts get lost in the swarf


Thread: Square Headed Screw Supplier
26/06/2019 23:15:03


When I made a few QC Tool holders I made the set screws from some square steel bar turned down and threaded.


26/06/2019 22:47:49


Rotagrip sell spare square headed set screws for the Dixon tool holders.


26/06/2019 22:47:48


Rotagrip sell spare square headed set screws for the Dixon tool holders.


Thread: What Did You Do Today 2019
25/06/2019 09:39:38


Yes the sample is about 1mm thick and I have used it on 1/16" anneal copper which is about the thickest I shall be doing. The darkened metal is just my bad lighting in the workshop. Although I do intend to blacken the steel to give a bit of rust protection.


24/06/2019 12:56:46

Finished my geared bending rolls. Made to the design of GHT. I already have some 12" rolls that I used when I was making a boiler, they are to heavy and cumbersome, so made a set with 5" rolls. More useful for the small work I now do.bending rolls 2.jpg

Thread: Boxford back gear
14/04/2019 15:24:41

Just measured the small back gear on my Boxford and it is 24 tooth 1.625 inches OD which makes it 16DP

Thread: Imperial Milling Machine
12/03/2019 09:32:08

I had the opposite. I bought a metric Tom Senior mill and being an old fart who can only work in Imperial. I fitted a three axis dro system to work in imperial. Since then I have never looked at the metric dials on the mill.

Thread: Vertex BS-0 Dividing Head 1-1/8 BSW Myford Spindle Nose
08/02/2019 20:32:05

Again bought my BS-0 about ten or so years ago and it has a 2 mt spindle. Have never had a problem with an attached Myford chucks even with heavy milling cuts.

Also made a Myford to Boxford spindle adapter to use the Boxfords chucks.

Thread: Small part holding
01/01/2019 11:15:08


I made this small parts vice some years ago and is very useful.

I believe it is a GH Thomas design and appeared in either ME or MEW magazine.

Regards Barry

Thread: What Did You Do Today 2019
01/01/2019 10:44:17

Watched the fireworks in Sao Bras (Portugal), with a few glasses of port and then to bed.

New years resolution to find my bag of Welsh steaming coal (if her indoors has not burned in on the fire) and get my boiler and Stuart compound steamed up.

engine boiler.jpg

Thread: What did you do Today 2018
29/12/2018 15:10:16

Bought a pair of ER25 collet blocks a while ago. As useful as they are ER collets don't hold short bits very well. So decided to make a pair of hex and square for my 3C collets. Just used some bit of steel I happened to have in a suitable size.

Collets are drawn in by a threaded ring.

Also made a 3C step collet out of brass to use for holding some cylinder covers I am making. Made from two pieces of brass brazed together (to save on waste).

3c blocks.jpg


Thread: MS 3mm x 25mm rivets?
04/08/2018 07:53:33

GLR Kennions list 1/8 X 1 inch

Thread: Left hand threads
08/03/2018 23:44:31

Many moons ago at an auto jumble I bought a box of three 5/16 BSF taps. Wasn't till I got home that I noticed the words "Left Hand' on the box. Never had a need for one, let alone three. If you have a problem getting one let me know and I will pop in the post.

Regards Barry

Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Sign up to our Newsletter

Sign up to our newsletter and get a free digital issue.

You can unsubscribe at anytime. View our privacy policy at

Latest Forum Posts
Support Our Partners
Eccentric Engineering
Rapid RC
Eccentric July 5 2018
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest