By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for Alan Jackson

Here is a list of all the postings Alan Jackson has made in our forums. Click on a thread name to jump to the thread.

Thread: Home Made Rear Toolpost Issue
02/03/2021 11:48:43

Here is my rear toolpost. The base unit has a sloped surface which enables easy height setting without affecting rigidity and the two hold down bolts screw into a long tee nut in the tee slot.

rear toolpost2.jpg

Edited By Alan Jackson on 02/03/2021 11:52:49

Edited By Alan Jackson on 02/03/2021 11:53:32

Edited By Alan Jackson on 02/03/2021 11:55:04

Thread: What about a "like" button on the forum?
19/02/2021 11:43:05

Perhaps there should be a vote on a like button, Like or do not Like. Just saying.

Alan

Thread: Split Collet in blind hole
05/02/2021 18:23:51

Just make the collet part too long so that it extends above the surface and clamp it in place endwise with a G clamp or toolmakers clamp while you drill the 8 mm hole. I found this is good enough to hold it in place while you carefully drill the hole. Cut the collet up to suit afterwards.

Alan

Edited By Alan Jackson on 05/02/2021 18:24:59

Thread: Collet runout. Is this normal
31/01/2021 11:32:26

What do you think of this spanner and ER32 fitting? There are 16 grooves and 15 holes in the nut, so there is always a zone for tightening/undoing the collet without locking the spindle.

Alan

10-ER32 collet spanner- ghosted.jpg

Edited By Alan Jackson on 31/01/2021 11:35:02

Thread: What Did You Do Today 2021
28/01/2021 18:06:51

My jab, two days ago, was at the Wickford community centre Essex. I was there just before the 11,10 appointment and out of the building by about 11,05. They could not have been more efficient and pleasant. Well done NHS.

Alan

Thread: Coronavirus death stats
16/01/2021 11:28:47

"As Michael says, Raphael, my heart is with you too and all of your colleagues that face this virus and potential exhaustion in dealing with it on a daily basis." Good true words.

Alan

Thread: Chipmaster variator
16/11/2020 18:49:59

I did a similar thing to my old chipmaster. I described it in MEW 253. Repacing the variator with a modern inverter solves the problem of a worn variator.

Alan

Thread: Vickers Bl 8 inch Howitzer cannon of 1917
26/10/2020 10:08:58

Magnificent work Mal. It will be great to see this when it can be exhibited.

Alan

Thread: Why is this guys mini lathe parting off so well?
23/10/2020 11:02:09

Here is my version for a parting tool. The cutting tool is in compression, avoiding the flexure due to the conventional cantilevered parting tool

https://www.youtube.com/watch?v=S8HvS13L7MU

Alan

Thread: New Moderators
31/08/2020 18:02:17

Welcome Mike & Dave, well done by you.

Alan

Thread: The Workshop Progress Thread 2020
09/08/2020 10:33:12

Roderick, your guitar is a beautiful work of art - congratulaions

Alan

Thread: ML7 3jaw pratt burnard
21/07/2020 17:08:50

fastdave & Martin kyte, I am certainly not nimble fingered; it is not hard to adjust the jaws so that each spacer can be pushed in position with the jaws set to a push fit so to speak. Once this is set up I just tighten the jaws up more and have 'not yet' found that the spacers have moved due to centrifugal force etc. I run the chuck at about 300 rpm or so, no problem. If you are very safety orientated I suppose you should make the ring arrangement shown earlier, but its a lot of work for such a simple process.

Alan

Edited By Alan Jackson on 21/07/2020 17:10:15

19/07/2020 18:20:10

I made three equal length spacers cut from a steel ring and insert them as shown . Works very well

Alan

Chuck jaw grind

Edited By Alan Jackson on 19/07/2020 18:21:56

Thread: Help please identifying a large vertical slide
14/07/2020 13:12:19

It is a Harrison vertical slide. Strong and solid

Alan

Thread: What’s the tolerance??
04/07/2020 10:50:49

The benefit that model engineers have is that they are the only one working on their project and as such can make any part near enough to the dimensioned size on the drawing. The mating part can then be made to match, but the art is knowing how the mating part has to fit and work to suit the required operations. If drawings were provided with machining tolerances, it would force the maker to comply with rigid requirements that would make the part much harder to produce, as well as require remaking in some instances to achieve a size which is often really only a dimension put on the drawing to show the general outlines etc. Tolerances are required for components made by various outside sources in order that other parts from other sources can fit together and comply with the design requirements.

Imaging making the drawings for a clock, say, with toleranced dimensions. It would force the designer to now legally comply with ensuring that every clock made to these drawings will run like clockwerk, sorry could not resist it. Have you ever tried to go through a design ensuring that the tolerance build ups (that is adding and subtracting the variations in a design due to component tolerance extremes) to ensure it can still function when the worse variations of the mating components come together?

Alan

Edited By Alan Jackson on 04/07/2020 10:53:43

Thread: Which Lathe???
02/07/2020 12:43:19

Very happy with my old Chippee - yipee!

Alan

Thread: ER32 frustration
29/06/2020 11:42:36

On my Stepperhead lathe the ER32 collet nut has two hardened discs positioned 120 degrees apart to act to remove the collet. I did it this way to avoid making the eccentric ring. This method has advantages in that it is easy to insert the collet and the hardened discs can be machined to a diameter and thickness to ensure they do not interfere with the concentricity of the installed collet.

Alan

Hardened discs for removal

Thread: Parting off
12/06/2020 18:36:24

With apologies for being flippant I wrote this some time ago

Alan

Vertical Parting Tool

A while ago I tried out a vertical parting tool it worked ok but I must admit I did not give it exhaustive testing to destruction etc.

In order to clarify the operation of a vertical parting tool here is my rather primitive description of how I think it works.

Imagine that you are the parting tool holder whereby your two hands are held straight out from you body. You hands are gripped together and your fists are the cutting edge. You have a friend who represents the metal being cut and he (If you are a front parting tool) pushes down on your hands while you do you best to resist him pushing down. You can see that he can quite easily push your arms down. If you want to now become a rear parting tool you can turn round 180 degrees and your friend would now push your hands upwards still he can easily overcome your resistance to him pushing up. So in order to stiffen you up, say you are frozen solid or have rigor mortise and are wearing a large pair of lead diving boots to anchor you down. When your friend (or should I now say de-parting undertaker) pushes down on you hands he will not be able to move your arms down because they are rigidly fixed to your body and he have to apply more force until you tip forward on you toes. Note that as you tip forward you rotate about your toes moving your cutting tool hands deeper into the metal being cut. If you are now rotated 180 degrees to become a rear parting tool your friend (some friend) now has to apply more upward force until you tip backwards on your heels. Also note that your cutting tool hands now move away from the metal being cut as you rotate backwards on your heels. Now you have to play the part of a vertical parting tool as I am proposing, so you now can be thawed out or de- rigor mortised. So lay flat on your back and push one arm vertically upwards and clench your fist to form the cutting tool. Your friend now has to apply considerably more force to overcome your vertical arm. Your arm will be in direct compression and until your elbow or wrist give way you will have much less a problem resisting his downward cutting force. It will also not matter if you are a front or rear vertical parting tool as long as the rotating force is pushing down on your hands. You can now get up and go back to your work or whatever you were doing. I apologise for being so flippant but I hope it does explain the reasoning.

Regards

Alan

Thread: Tallyho project
10/06/2020 16:19:24

Sorry I mis spelt the Topic title can it be corrected?

Alan

10/06/2020 16:04:11

I have just been watching on youtube the rebuilding of an old sailing ship see

https://www.youtube.com/watch?v=7wdqZwc2Nyo

This is certainly not model engineering but it shows the superb skills in being a shipwright on a wooden boat. Well worh watching

Alan

Edited By Alan Jackson on 10/06/2020 16:09:19

Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Latest Forum Posts
Support Our Partners
JD Metals
emcomachinetools
ChesterUK
Eccentric July 5 2018
cowells
Warco
Eccentric Engineering
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest