By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for ega

Here is a list of all the postings ega has made in our forums. Click on a thread name to jump to the thread.

Thread: Help needed truing ways on mill
22/02/2014 10:21:36


Many thanks indeed to all of you for your very interesting and constructive posts. The variety of approach has been quite striking and I am going to have to mull it all over before deciding what to do.

Robbo: in answer to your question, I don't think I can improve much on the paragraph immediately under the photo in my original post; the areas where the *coarse* machining marks are visible are indeed the low areas and the remainder of each way shows the marks of *fine* machining. As I said, I am puzzled by all this; if the casting had warped I would have expected the other side not to be flat.

Thread: Ruby Loftus Screwing a Breech-ring
22/02/2014 00:44:59

Billy Mills:

Spot on! Third Age Matters was indeed where I saw the reproduction. It's fair to say that the article was mainly concerned with the artist rather than her subject - two women who were both very good at their jobs.

Comments to the effect that this was a production operation rather than a tricky one-off seem to be on target, too, but the artist is obviously seeing the romance in the subject and, perhaps, making a point about women's capabilities. If this was a purely production process than the firm-joint calipers and swan-neck toolholder have perhaps been introduced for artistic effect. I remember reading somewhere that WWI inspectors (female) could detect a very small taper with their fingers.

Thread: Help needed truing ways on mill
21/02/2014 21:21:40

I have just stripped down my Warco Economy Mill/Drill and was dismayed to find the upper Y-axis ways had been poorly machined. I have uploaded several photos to an album but the situation can be appreciated from this upside down view of the sliding base:


At opposite ends of the ways it seems that the finishing cut has not covered the full length (near end on left and far end on right in photo, see album for other views). I have checked that the underside as seen in the photo is flat and micrometer measurements indicate that the bad areas are about three thou low.

I am in Rochester, Kent. Is there anyone reasonably near, please, who is willing and able to help? The base is about 195 x 240 in size and the ways appear to have been milled rather than ground so I am looking for someone with a large mill. As an alternative to a helping hand, can anyone recommend a suitable machine shop in the area?

This machine has met my modest needs for many years and I suppose I could just reassemble it, keep calm and carry on. The only other in-house possibility seem to be the doubtful course of facing this heavy lump on the lathe faceplate followed by scraping.

Incidentally, I am rather at a loss to understand how the defective result has been achieved given that the other side is flat.

Thread: Ruby Loftus Screwing a Breech-ring
21/02/2014 18:55:12

Thanks to everyone who responded and apologies to Oompa Lumpa!

Thread: Milling machine X and Y axis out of square
19/02/2014 15:29:09

Comments on this interesting and lively thread:

1. I have had numerous good buys from Warco over the years and also a rotary table which I asked them to exchange and a bench grinder which they agreed to take back; on both occasions they were entirely cooperative. I agree that good communications are vital if you want happy customers. It is worth remembering that the purchaser is not limited to the seller's warranty and may well have a statutory remedy after its expiry.

2. ISO 9001: my then employers put us through the process of certification some years ago. I agree with the Wikipedia comment.

3. I have some fellow feeling for the OP who has installed heavy equipment and is not now sure he can get it out again. One of the first jobs for my new combination woodworker was the making of new workshop doors ...

I look forward to a happy ending.

Thread: Polymer bearings
19/02/2014 14:43:08

Derek Beck had quite a lot to say about these bearings in his ME series "First Affaire with a Lathe".

Thread: Linking to free web content is legal, says EU Court
15/02/2014 00:49:55


That was probably me in my Ruby Loftus thread - many thanks for the link!

I believe I could have provided a *link* to one of the many images of the picture concerned but I wanted to provoke a broad discussion. That said, posting a copyright image to the thread itself may well be a different matter and I preferred to err on the side of prudence; respect to the resolute poster who did so!

Thread: Ruby Loftus Screwing a Breech-ring
14/02/2014 18:28:08

Neil Wyatt

Thank you for referring me to the IWM licence. You are right that I had not read it. A quick look raises the question of whether reproducing the painting on this website would be a non-commercial use. I am all in favour, however, of a robust attitude to copyright rules. Was it here that the Clarkson Autolock instructions were not reproduced for fear of repercussions? (I think commonsense ultimately prevailed).

I believe the breech-ring in question is for a Bofors gun.

Thread: How do I put a leadscrew handle onto my Boxford, please?
14/02/2014 17:13:07

Leadscrew handwheels are no doubt less common on larger lathes. Having been used to a Myford S7, when I got my Willson slantbed I soon missed the facility and so fitted the one shown in the picture. The leadscrew was drilled and tapped in situ with the help of a simple jig so to allow an extension to be fitted to carry the new wheel made from a redundant vee pulley with handle bought in from Arc Euro. With the saddle fully to the left I can comfortably rest my hand on the rim of the handle to put on cut. I have yet to figure out a satisfactory way to incorporate a graduated, re-settable micrometer ring.

BTW, the black appearance of the ways is due to the presence of covers made from plastic angle.


Thread: Ruby Loftus Screwing a Breech-ring
14/02/2014 16:29:02

I was struck by a reproduction of this painting which was new to me but which is readily available with background information via Google, etc. The technical detail in the painting is impressive but can anyone identify the lathe and, in particular, the device that her right hand rests upon?

This was a very demanding operation and I saw a comment to the effect that a group of incredulous (male) toolmakers had visited the factory to verify the truth of the picture.

BTW, I thought about posting a scan of the painting but it is copyright the Imperial War Museum and I don't want their tanks on my lawn!

Thread: Announcement re: Model Engineers' Workshop
13/02/2014 16:39:19

I have mixed feelings about being reminded that I have been reading MEW for nearly a quarter of a century but am glad to join in the welcome to our new editor!

Someone mentioned "the new copyright agreement"; is the text of this available, please?

Thread: making writing visible
30/01/2014 11:10:19

Have you tried "brass rubbing" ie laying a sheet of paper over the work and using pencil or other medium to try to pick up the scratch marks?

Thread: Hot bandsaw........
16/01/2014 16:07:47

The manual for my Warco bandsaw gives the following possible causes for motor running too hot:

  1. Blade tension too high
  2. Drive belt tension too high
  3. Blade is too coarse for work
  4. Blade is too fine for work
  5. Gears alligned (sic) improperly
  6. Gears need lubrication
  7. Cut is binding blade

I realize that Rik Shaw has a much later and different machine but this comprehensive list does suggest some possibilities for investigation. 1 - 6 are self-explanatory; the corrective action for 7 is to adjust the guide bearing clearance. My motor runs hot too, but thirty plus years on the saw is still working well, currently with a bimetallic blade from Stub Mandrel's supplier.

Thread: What have you recycled today?
11/01/2014 17:16:38

Russell Eberhardt et al:

Thanks for the further microwave information. I think I now understand why the internal light can be seen through the glass door. BTW, we used to hear a lot about the dangers of mobile phones overheating the brain but their present popularity seems to have overridden that concern.

andrew winks:

On the subject metal identification, John McNamara mentioned beryllium and I was intrigued to see from his link that the proportion of the element present could be assessed by tasting - sweeter indicates more, but, obviously, this test is not used today. I believe that the strength of car antifreeze used to be assessed by tasting.

10/01/2014 15:06:51

John McNamara:

Thanks for the advice and useful links.

Quite apart from the perils of dismantling, I gather that there can be danger from stray m/w radiation. I understand this is normally contained by the polarised screen in the oven door and wonder why it is nonetheless possible to see inside.

10/01/2014 14:58:28


Thanks for your advice. Is the UV exposure something to do with etching the PCB?

On a different point, it did occur to me that the built-in turntable and fan might be useful for small-scale spray painting.

09/01/2014 23:38:57

Michael Cox 1:

Many thanks for the useful advice.

Michael Williams:

KRW is sorely missed - I am still using stuff bought years ago from his "cat".

09/01/2014 17:13:54

Has anyone recycled a micro wave oven? The keypad on my very old one is getting temperamental and in view of its age I am thinking of getting a replacement oven.

I gather there is a device called a magnetron in these things. This oven is very heavy and I am wondering what I might usefully salvage from it. Are there likely to be dangerous residual voltages inside?

Thread: Myford Super 7 Headstock Lubrication
30/12/2013 16:59:00


Thank you for elaborating the point I made about holding the wick down; it is, of course, on *replacing* the spindle that this is important..

Did you research the spec of "Three-in One"? It seems from the 3-IN-ONE website that it is indeed a mineral oil but I couldn't see the viscosity stated. Instinctively, I would be wary of using such a general purpose product on my precious lathe.

The mark 1 Super Seven headstock lubrication was different and I wonder if anyone has information as to why it was changed.

30/12/2013 11:28:13

IIRC, when removing the spindle you have to restrain the wick from moving upwards by sticking a bit of wire or similar through from the side.

Possibly an opportunity to replace the belt if you use conventional vee belts (countershaft would have to come out too, of course.

Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Support Our Partners
Eccentric July 5 2018
Rapid RC
Eccentric Engineering
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest