By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for steamdave

Here is a list of all the postings steamdave has made in our forums. Click on a thread name to jump to the thread.

Thread: Thiel 158 problem
13/11/2011 15:01:44

Hi Rob

Thanks for your input. I will check on the detent next time I can get to my workshop - I'm away at work now. The Y axis did overrun the normal travel limit, but I don't remember any problem afterwards with the feed selector not being able to engage. I engaged the selector but there just wasn't any feed. That is why I wondered about the hidden shear pin.

Dave

The Emerald Isle

13/11/2011 14:53:13

Hi Bob

Thanks for your suggestion. I do have a manual, but it must be based on a later type of machine than mine because there are several differences in it and crucially no shear pin is shown.

Dave

The Emerald Isle

12/11/2011 17:42:58

Does any reader have a good working knowledge of the Thiel 158 milling machine - or know anyone who does?

I have lost power feed to the Y axis. There must be a shear pin somewhere that has failed, but where?! I know about the main one on the left hand side of the column and that one is intact.

Hopefully someone will be able to help.

Dave

The Emerald Isle

Thread: Double acting petrol engine
16/04/2011 12:45:11

There was also the Mery engine of about 1890. Double acting 6(?) stroke. Casting kits are available from Morrison & Marvin and is a very popular engine build in the US.

Dave

The Emerald Isle

Thread: Thiel 158 milling machine woe
13/03/2011 14:26:23

Graham

Thanks for your suggestion. I'm over in England for the next week and will let you know what I find out when i get home.

Dave

The Emerald Isle

10/03/2011 15:44:59
Is anyone familiar with the workings of the Thiel 158 Duplex milling machine?



Whilst making brackets for fitting a DRO, I removed the Y axis power feed stops and the power feed overran its travel and the Y axis shear pin sheared.

Question: Where is the Y axis shear pin located? I know the main one on the left hand side (and it is intact), but I believe each axis has its own shear pin.


I have asked this question on a couple of other fora, but so far no response. Is the Thiel such a rare beast?!




Dave

The Emerald Isle



Thread: Low tension coil
18/08/2009 08:17:22

Thanks Ian and Johan.

Seems like I need to look for an old fashioned Fluorescent starter!

Dave

The Emerald Isle

17/08/2009 03:39:27

Hello all

Does anyon know a source of low tension coils in the UK?  I need one for an igniter fired hit 'n' miss engine. Hemmingway does not stock them.  I would imagine a call to one of the US engine specailists is required, but which one?

If no source is known, is it possible to use a normal car / bike / lawn mower 6v coil and just use the secondary winding (keeping the primary out of circuit)?

Dave

The Emerald Isle

Thread: Readership survey
09/07/2009 15:46:37

David Clarke

Just to let you know I arrived home in Ireland today from working in Saudi Arabia.  My survey will be in the post tomorrow morning.  Hope it is not too late!

Dave

The Emerald Isle

Thread: Piston Ring Material
26/06/2009 18:26:28

Perhaps someone like College Engineering Supplies would be able to give you a definitive answer.

Dave

The Emerald Isle

Thread: RLE Engine
24/06/2009 20:48:32

Alyn Foundry ceased trading from April 2008 for various reasons.  Graham Corry still retains the patterns and drawings for the designs (although not all the designs were drawn up).

The business was/is up for sale, but the asking price was a bit unrealistic considering today's economic climate.

As far as I know he has no stock of any castings for his engines.

 

Dave

The Emerald Isle

Thread: Ignition coils for small engines
24/06/2009 20:35:27
Posted by Stick on 05/06/2009 16:02:01:
  
At the moment I am using the Jerry Howell Buzz coil circuit on my RLE Hit and Miss engine, these circuits had to be made up from components, the systems on the above site are ready to go which sounds good.
Mike.

 Unfortunately, Jerry Howell doesn't produce the buzzcoil circuit kits any longer.  They are now available from

http://home.pacbell.net/daveanne/index.html

but at a huge increase in price.

Or you may want to go the deLuxe route and try

http://www.thehermitsmachineshop.com/Model_T_Buzzcoil.html

 

Dave

The Emerald Isle

Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Latest Forum Posts
Support Our Partners
Eccentric July 5 2018
rapid Direct
emcomachinetools
Warco
walker midge
cowells
JD Metals
Eccentric Engineering
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest