By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for David Clark 1

Here is a list of all the postings David Clark 1 has made in our forums. Click on a thread name to jump to the thread.

Thread: Clarkson autolock chucks
10/07/2009 10:21:39
Hi There
I think that the shank are morse taper 0 or 1.
It is over 35 years since I measusred one.
Perhaps you could buy an old S type chuck with a decent centre and fit it to yours.
You could probably pick up an old 40 international one for a few quid.
regards David
 
 
Thread: WARCO have had phone problems.
09/07/2009 16:36:48
Warco would like to apologise to everyone who might have had difficulty making contact be telephone recently. We applied to ISDN with the purpose of
enhanced line clarity. BT surveyed our site and confirmed that we could
be connected.

The engineer who came to make the connection said that we
could not be connected to ISDN. Some days later our phone lines were
disconnected, due we are told to the fact that the engineer did not
report that he was unable to make the connection, consequently when the
telephone exchange tried to switch from analogue to ISDN it cut the
lines off. It took 24 hours to reverse the situation.

Worse still, one day later we were disconnected again with another 24 hour wait. Again, our apologies. BT have a lot to answer for.
Thread: Northumberland locomotive additional dimension
08/07/2009 17:33:06
Hi There
The position of the angular line of the cylinder centres runs out at 3/8in. from the extreme top of the frames.
regards David
Thread: Thread Notifications
08/07/2009 16:07:57
Hi There
If you look below the editor, you can add additions to the currrent thread to be notified to you by email.
I don't think there is a way that all posts will be notified.
regards David
 
Thread: New Subscription Freebies
08/07/2009 15:37:55
Hi Ian
Why don't you write it up for Model Engineer?
regards David
 
Thread: The Best of Model Engineer Volume one - next special
08/07/2009 12:38:26
Hi There
I have decided to give the complete set of Boxhill plans free in the next Special.
This is a 5in. gauge model of the Brighton Terriers by Martin Evans.
 
It is an established design and many succesful locomotives have been built.
regards David
 

Edited By David Clark 1 on 08/07/2009 12:38:49

Thread: Model Engineer Page Count increase and free plans
08/07/2009 12:32:47
Hi Tere
I am looking at Springbok in 5in. gauge.
A large but very popular loco.
This is about 12 sheets over 12 issues.
regards David
 
Thread: Latest Special is in Smiths
08/07/2009 12:30:56
Hi There
A lot of thespecial magazine seems to be sitting in Smiths stock rooms around the country.
Ask the staff to go and get them out for you.
regards David
 
Thread: A professional boiler - poor service
07/07/2009 09:47:57
Hi There
Anyone buying a custom made boiler should ask for references from recent previous customers. This should help when deciding a boiler maker.
 
Anyone with a long delivery time may well be a one man band who produces a good product and has a big order book.
 
You should also ensure you know who who is making the boiler and that it is not being sub contracted.
 
If anyone would like to post recomendations of good boiler makers they are welcome to do so as long as they have no connection with the firm.
regards David
 
Thread: vega v twin for stroke aero engine
06/07/2009 15:40:29
Hi There
A photocopy of an article for personal use is OK.
It is classed as reasonable educational use I think.
Plans are available from MyHobbyStore but they are not listed on the web site.
I will see if I can get them added.
regards David
 
 
Thread: Milling on Myford
06/07/2009 06:11:41
Hi There
Probably a slot drill.
If milling a flat surface, put a small chamfer on the corners of he slot drill.
regards David
Thread: GEAR WHEEL SUPPLIERS
05/07/2009 20:31:16
Hi There
Try googling HPC gears.
regards David
 
Thread: Milling on Myford
05/07/2009 20:30:11
Hi There
I would not use a rippa for milling in the lathe.
regards David
Thread: Building a GWR Bulldog locomotive
05/07/2009 11:00:48
Hi There
Drawings are straight frames.
I have access to all drawings.
The Dukedog is parallel boiler, Dulldog tapered.
I thought curved frames were covered in article in magazine though.
regards David
 
Thread: Coventry Diehead
05/07/2009 07:14:41
Hi There
I ttink you go aniti clockwise when using left hand dies.
regard David
 
Thread: vega v twin for stroke aero engine
03/07/2009 23:35:22
Hi There
Vega is not listed in the plans handbook.
regards David
 
Thread: Building a GWR Bulldog locomotive
03/07/2009 23:30:28
Hi There
The drawings cover Bulldog and Dke Dog.
I think the duke Dog is the rounded frames.
regards David
 
Thread: Lathe height?
02/07/2009 18:16:57
Hi There
Elbow height to cross slide handwheel height.
Bend elbow, you should be able to turn cross slide with arm horizontal.
regards David
 
Thread: plastic containers
02/07/2009 08:00:40
HI There
Yes, that is them.
£4.99 for 5 can't be bad.
They are good quality mouldings, not cheap blow mouldings as you would expect.
regards David
 
Thread: Magazine Latest Issue advert
01/07/2009 18:02:45
ME was late because the printers posted it on Monday instead of Friday.
I finished the magazine a day early as usual.
regards David
 
Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Latest Forum Posts
Support Our Partners
cowells
JD Metals
BOLDON
Eccentric July 5 2018
walker midge
rapid Direct
emcomachinetools
Warco
Eccentric Engineering
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest