By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for DiogenesII

Here is a list of all the postings DiogenesII has made in our forums. Click on a thread name to jump to the thread.

Thread: Odd sleeve
05/01/2020 18:12:02

I think Nick has it.. Hot forging in a die using a mandrel of the correct shape?

05/01/2020 11:00:48

..Broached? ..is there a wedge-slot at the back? ..it looks like one of those processes that sprang from their gun industry..

Thread: Imperial supplies of mild steel
04/01/2020 11:05:07

GLR Kennions still supply in 3/4 & 1" widths..

Thread: Hobbymat lathe - couple of questions
03/01/2020 18:21:24

Hi Chris. The standard milling table that Hobbvymat supplied is aluminium alloy, and the vise bolts length-wise to it, i.e. jaws parallel to slots.

If you want (or need) to use the vise with the jaws in the other orientation, it can be bolted directly to the topslide - using one mounting hole beneath the toolpost, and the other is the one between the toolpost and the back of the slide (if you wondered what it was for.. it's usually plugged with a slotted grubscrew) ..be mindful of the length of the bolts used - there's very little clearance between the upper & lower parts of the slide, and also, be gentle when tightening either the vise or the toolpost when fitting - the standard bolts have a shear groove in them to prevent overtightening (and bowing or warping the topslide)

Thread: RMC Type-B Engine Build
03/01/2020 17:53:49

Ha, that brings back the days of the Colourtune! ..seriously though, that's a very clean & consistent burn - do you know what fuel it's running on in the video?

Thread: mystery collet for Prazi SD400 lathe
03/01/2020 06:41:14

Thanks for the information Peter, I suspected that the answer would lie in the DIN system somewhere - the smaller Hobbymat/Prazi/Saupe Sohn machines with which I am more familiar never seem to have been supplied with draw-in collets and instead used a small spindle-nose chuck taking DIN 6343 F17 125E collets..

02/01/2020 22:02:04

Well. Clearly a vexed question.. anyone?

Thread: A 5cc Twin Shaft diesel engine
31/12/2019 19:33:16

All of this was a completely unknown world to me until the 'Viper thread.. now I find I'm really looking forward to watching things develop, many thanks all.

Thread: Hobbymat lathe - couple of questions
31/12/2019 13:36:25

Well reminded, Bazyle -

The 20T gear carrier comprises a simple stepped cylinder 21.7mm long. The central bore is 8mm (ream if possible).

The larger part of the component has a diameter of c.19.98mm (light push fit for a 20mm bore) and is 10.2mm long. It has 4mm wide key slot, 2.6mm deep (which could be formed by hacksaw and file if necessary - aim for perfection, but settle for adequate - it doesn't run at high speed or take a great load, and mates with a moulded component).

The reduced part that carries the 20T gear is c.13.6 to 13.7mm in diameter (mine is firmly fixed and I'm not going to prise it off!), the dimension isn't critical as the gear is permanently affixed by pressing onto the carrier, so make matched components - aim for a fit that requires say, light vise- rather than finger- pressure, but without "stretching" the gear too much - again, a tiny inaccuracy here isn't the end of the world as running clearance is established whilst setting up the gear train in any case. If one could arrange a parallel knurl, this would be exactly the job for which that process is intended, but failing that any knurl would probably do.. An adhesive might do, but I'm not sure that all are effective on plastics - advice welcome!

The gear should be 11mm thick, leaving 0.5mm of the carrier projecting beyond the face to provide axial clearance for the gear once the carrier is secured to the stud with it's screw & washer.

Both outer edges and the ends of the internal bore should be generously chamfered, for ease of fitting, to reduce friction, and to allow the ingress of oil.

In order to cut the blanks for any of these 1Mod gears, simply take the number of teeth required and add 2 to arrive at the finished diameter in mm - thus 30T = 32mm, 60T=62mm, 100T=102mm etc. With the exception of the 20, which is 11mm, all the others are 10mm thick.

I'd get a piece of Leaded ("free-machining" Bright Mild Steel Round Bar (EN1APb) for this job (I note the standard item is "soft", probably to save wear on the studs), and it's an exceptionally pleasing material to work with.

Edited By DiogenesII on 31/12/2019 13:38:05

28/12/2019 18:02:35

The gears appear to be 1.0 MOD, are 10mm thick, and have a 20mm bore which is slotted to accommodate a 4mm key.

(50T gear=52mm OD, 60T=62mm, 70T=72mm, = 1mm of PD per tooth plus the addendum (= to mod) on each side).

I can't establish the pressure angle exactly from my worn examples, but 20 degrees seems the most likely to me - it's a "modern" metric machine made in Europe, for those not familiar with it - additional informed comment or confirmation would be very welcome, here.. (..although if you are going to get a set printed, it's rather immaterial in any case, as long as they are all the same.).

You will need; 20, 30, 35, 40, 50, 55, two 60's, 65, 70, 75, and 100, if you want every option listed on the plate. Even for common metric threads you will still need 30, 35, 40, 50, two 60's, 70, 75 & 100. A 20 is "nice-to-have" for a fine finishing feed.

I'm not familiar with the mini-lathe change-wheel sets, but do be aware that the Hobbymat uses a 1mm pitch leadscrew, which I think is finer than that fitted to ?most mini-lathes and therefore the ratio between headstock-spindle-turns versus amount-the-carriage-advances will be different.. might be worth doing the maths/checking the tables before buying any gears, just to make sure that you will be able to achieve the ratios that you need.

Good luck!

Thread: Strange digital caliper behavior
21/12/2019 08:58:00

Dependent on your calipers, it may be that you may just need to reset the origin.. ..not all have this facility, but some have an "origin" button, and others have a small hole to access the reset switch with a paperclip or similar..

It's just a reset for the original "0" calibration..

Thread: "Reclaimed Iron Cogs" on Ebay UK
20/12/2019 17:52:03

Jon, ...it's also not uncommon for that sort of thing to get separated at auctions or estate sales, where neither vendor, auctioneer, or sometimes even purchaser actually knows what any of the lots actually are..

Thread: What Did You Do Today 2019
20/12/2019 07:20:05

Andrew - ..just food for thought, but having slept on the idea, might it be easier to form a shallow cone by starting with a plain cylinder (and removing a long thin fillet) rather than a flat sheet? ..you'd have a bit more control of the metal..

Thread: MR16 LED Spot lights
19/12/2019 09:42:42

Just for the sake of "completeness" ..the MR16 also has a pair of opposing grooves on the "neck" above the pins which are provided for retention by a clip on some types of holders.. but like others have noted, it'll be easier to contrive a blob of something sticky..

Thread: "Reclaimed Iron Cogs" on Ebay UK
19/12/2019 09:15:12

..knew I should have bought them.. ..next time you see them they'll be £150..

18/12/2019 19:52:02

Not on familiar territory here, but could those splines be ?Colchester-ish?

The smallest is stamped "30B", didn't manage to successfully count the largest..

**LINK**

Apologies if this is a clumsy link, just thought they might be of interest to someone..

Thread: Myford Super 7b lead screw end float
18/12/2019 07:13:13

..maybe the most careful assembly and close tolerances are to be found in the structure of Hemingway's opening paragraph wink

Thread: Screwcutting on the lathe
03/12/2019 07:28:54

"I've moved the cutter forward with the top slide until it just touches the bar. I set the zero on the top slide and advanced it 0.92mm (3 and a bit divisions off a full turn).

Next zero the cross slide and the top slide. Move the topslide back until it just touches the bar again (a bit over one turn)..."

Your tool point looks fine - when you say "move the topslide back", you need to come much further back, and then go forward again to touch, in order to remove any backlash in the feedscrew..

..at present it sounds like you are touching off, turning less than a full turn (to achieve "full depth" zero), then coming back over 1 full turn to touch again.. try coming back, say, 3/4 of a turn, and then go forward again for your final touch..

sincere apologies if I have misinterpreted...

Thread: Annealing Brass
01/12/2019 09:35:30

+1 for heating to dull red and allowing to cool naturally.

Could part of the problem be the "right angle" requirement - if you are attempting a sharp 90 degree angle, it's asking a lot of the ductility.. It would be much easier if you were able to form the bend over a radius, if there is scope within the design for this to be practical..

Thread: Inside chuck jaws
26/11/2019 08:37:24

I once owned a 3j scroll chuck with reversible jaws - ancient (it came with a Brittania), maybe a "Crown", 4(-ish) inch size (memory gets rather treacherous here).

IIRC (and I think what Robin means), it isn't that the jaw positions change relative to the slots, it's just that their sequence of engagement with the scroll is reversed, in that "3" requires engagement first, and "1" engages last..

Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Latest Forum Posts
Support Our Partners
ChesterUK
JD Metals
Eccentric July 5 2018
Warco
cowells
emcomachinetools
Eccentric Engineering
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest