By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for Bob Wild

Here is a list of all the postings Bob Wild has made in our forums. Click on a thread name to jump to the thread.

Thread: Has anyone bought and built a Myfordboy engine
05/01/2021 22:47:55

I built his traction engine. A few pics here:

**LINK**

Quite pleased with the castings and drawings although I did customise it a bit to make it look a bit better (to me). David Abbot, myfordboy, was most helpful and answered my email queries.

Bob

Thread: Workshop temperature - cold
04/12/2020 22:58:33

What a load of wimps on here. Just spent an afternoon in the workshop at 1.0 deg C. Done a load of milling with a glove on one hand to reduce the conductivity from an aluminium handle. But it was most successful 😋😋

Edited By Bob Wild on 04/12/2020 22:59:31

Thread: Lady Stephanie
27/11/2020 23:21:27

Bother. I wish I had seen this thread earlier. I built Lady Stephanie recently. No problems but the supplied drawings were almost unreadable, so I used the magazine articles. There is a funny story (now). The entablature casting was terribly distorted so I sent it back to the address on the drawings. No response after a while so I phoned Reeves. They said that they moved from that address many years ago so my parcel was lost! They refused to send me a replacement until I gave them the original. Despite the fact that they had given me the wrong address they were unrepentant and I had to give up in the end. So I prefabricated the entablature myself in the end and put Reeves on my list of non-preferred suppliers 🙁🙁

Thread: Good YouTube videos
21/11/2020 22:03:55

Where’s Clickspring. He’s very good but hasn’t posted for ages?

Thread: Cosworth V8 1:12 scale
15/11/2020 22:50:44

Very impressed!!

Thread: Merryweather Fire King
11/11/2020 23:00:44

These brackets look fairly straightforward, but they have given me a real headache. So I thought they deserved a mention in my build thread::

too big brackets.jpg

The drawing called for them to be bent from 3mm strip. But I wasn't confident in making the double bends in the right place, so decided to machine from solid. Two pieces were glued together so I could machine them as an identical pair. I chain drilled first to remove as much metal as possible:

chain drilling.jpg

This is where the problems started. Because I'm using Stuart cylinders I had to recalculate the width, and somehow while allowing for the 3mm thickness I ended up with then being 3mm too wide. I couldn't face throwing them away and starting again, so I cut off one face and screwed and glued another piece of machined angle. This gave me the opportunity to use JB Weld for the first time:

correct brackets.jpg

I painted the chassis while I was at it, and here is the pump assembly finally in position:

pump assembled.jpg

Next up, a leek test. I have learned from bitter experience not to delay this!!

Thread: Grumpy old men
10/10/2020 22:53:20

People who say “myself” when they really mean “me”

Thread: Merryweather Fire King
10/10/2020 22:48:42

Oh Paul, this is hard. I suppose I need a non-windows photo editor. But I think I’ll just stick to landscape in the future!

Bob

Thread: How do you seal engine joints?
10/10/2020 22:45:00

Thanks for all your useful suggestions. I think I know what to do now. Let’s hope for the best.

Bob

08/10/2020 22:56:57

I have just finished the water pump for my Merryweather Fire King. This the first working engine I have made, so I have no experience in sealing the joints. There are flat surfaces, screwed parts and some glands.


What’s the best way to do this? What should you pack the glands with? I have some fibre paper, Hylomar Blue and ptfe tape.


Bob

Thread: Merryweather Fire King
08/10/2020 22:27:51

Don’t understand that Paul. That image you did was just as the original on my PC. Could it be something to do with the fact that the original was taken with an iPhone. I have seen other issues between iOS and windows?

07/10/2020 22:50:25

Thanks Paul. The plans are from Julius de Wall based on a design in The Engineer magazine from 1908. There is a layout drawing and a lot more detail in the first post of this thread.

Here is a rotated image of the pump. It has rotated the whole lot; so not much help. And you can see that if I crop the image half the detail will be lost. NBG

boiler feed pump l.jpg

Bob

06/10/2020 23:19:16

Well I'm back from my tour of the UK from the Lake District to The Yorkshire Dales by way of Devon. In between pitstops I've managed to get the water pump finished. Here are the parts:

pump parts.jpg

And here is the assembly complete with the steam cylinders:

pump and cylinders.jpg

and placed in the Merryweather:

pump assembly.jpg

Before I go any further I need to pressure test it. Been racking my brains thinking about how to do it and then it came to me. The Merryweather already has a hand pump for the boiler feed, so I can use that. And here it is:

boiler feed pump.jpg

My only problem when I build it is how to seal the joints. I have some fibre gasket material, Hylomar sealant and some PTFE tape, but haven't a clue which to use and where. Or should I get something else? Any suggestions would be most appreciated.

Incidentally, I have just realised that this forum doesn't like Portrait photos. Note to self for the future.

 

Edited By Bob Wild on 06/10/2020 23:21:13

Thread: What cleaning solution?
05/10/2020 23:19:04

Thanks chaps for all your replies. As a bit of background I should have said in my original post that my immediate need is to clean up the parts of the water pump for my Merryweather Fire King. This has two double acting cylinders that I lapped with grinding paste. The pump bodies have eight ball valves and an internal rabbit warren of holes, many of which are plugged which prevent direct access for cleaning.

So I have decided to use white spirit as I already have a gallon of the stuff.

Bob

02/10/2020 23:46:38

Many years ago when I worked in an engineering company, components were cleaned in a trichloroethane bath. This is now banned, so I wondered if anyone could suggest the acceptable alternative for washing out swarf and grinding paste?

Bob

Thread: Where's this rust come from ?
01/10/2020 23:43:12

Thanks chaps for all your divers comments. I should have mentioned that it was a new product and my workshop is pretty dry without the need for de-humidifiers.. I'm inclined to the opinion that it was caused by some reaction with the felt or glue. I'm puzzled as to why I should have the problem when other purchasers of this tool box have not.

Anyway, I've reported the problem to the supplier and asked for my money back. Watch this space (slowly).

Bob

30/09/2020 23:35:15

Two months ago I bought a tool chest in an attempt to tidy up my workshop.

toolbox.jpg

To my horror many of the tools are going rusty, like this V Block for example:

v block.jpg

The only surface affected is that in direct contact with the bottom of each drawer. It look like there is a layer of material which looks like baize (but is not) glued to the wood and the parts are actually stuck to this. So the question is what has caused this, and more importantly how can I prevent it ?

Thread: Change to the Code of Conduct
28/08/2020 23:05:16

I notice that there are a miriad of opinions, one for each person who replies. I can only reflect on when my company decided to redesign our software. So we gathered all interested parties and each and everyone had a different idea what the look and feel should be. In the end I said “yes” and some time later said “this is what it will look like” (actually based on the colour of my car). Sometimes what you need is a Benevolent Dictator

27/08/2020 10:13:50

#JasonB - Apple changes the name of a file when using an iPhone to something incredibly long which makes photos in an album unidentifiable

27/08/2020 00:37:31

I’ve read the comments above about members posting on other forums as well as this. I indeed do just that; because as a relative beginner I look for as much help and advice from experienced model engineers as I can get.
And I notice a few comments about the shortcomings of the technology of this forum. My biggest and really serious gripe is the torturous way of inserting photos into a post from my iPhone. It is a real pain to have to email a photo to my pc, then rename it and load it into an album before inserting it into my post. That is four steps, not to mention having to go from my workshop to my pc, whereas in the other forums I can upload a photo directly from my phone  into my post. I’m sure you are losing a lot of potential content because of the effort involved. I would certainly do more if it were easier.

Edited By Bob Wild on 27/08/2020 00:41:27

Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Latest Forum Posts
Support Our Partners
cowells
Eccentric July 5 2018
Dreweatts
Eccentric Engineering
Rapid RC
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest