By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for David George 1

Here is a list of all the postings David George 1 has made in our forums. Click on a thread name to jump to the thread.

Thread: Just arrived (knew of the Mag but not the forum - oops)
05/06/2020 22:21:04

Welcome to the forum. The surface grinder sounds pretty good. Can you program a profile to grind as I always thought that would be great.


Thread: New to area and this forum
04/06/2020 17:58:31

Hi welcome to the forum. I am sure that you can contribute much to the forum on CNC and programing and maybe get some information on projects back in return.


Thread: Silver soldering boiler
03/06/2020 20:01:14
I couldn't wait to try out boiler evan though I was still waiting for the brass plate for top cover.

Edited By David George 1 on 03/06/2020 20:03:54

Edited By David George 1 on 03/06/2020 20:05:17

Thread: Merryweather Steam Fire King self propelled
03/06/2020 13:35:09

Absolutely magic. It shows what a well made scale model can do.


Thread: Silver soldering boiler
02/06/2020 19:39:40

Decided to pressure test the boiler. As I didn't have a pressure pump I had to make something and with a piece of 1 1/2 mild steel drilled and reamed a 1/2 bore and cut a 3mm o ring groove to make a seal for a dowell for a plunger. Then I drilled a cross hole 4mm though and tapped them 8mm about 10mm deep. I then made two non return valves from a piece of brass two 5mm balls and a couple of springs one suck and seal, one pressure and seal, just make sure the spring is on the right side. I Soldered a couple of pipes into the non return valves one with a connection to boiler and a suction pipe to pick up water.

David George 20200602_165644.jpg


When I conected the pump to the boiler which I had pre filled with water the pump worked great and found a couple of leaks one on the level plug which needed a new washer as the copper one I made didn't seal but a bit of PTFE fixed that for now and the seal on the fitting which holds the pressure gauge had a slight leak at pressure a bit of solid locktited thread seal fixed that.


The boiler was ok in itself and holds pressure up to 60 PSI that is as far as the gauge goes. I replaced the grub screw with the safety valve and tested it and it released at about 20 PSI I hope that is enough to run the little wobbler.



Edited By David George 1 on 02/06/2020 19:42:20

Edited By David George 1 on 02/06/2020 19:43:23

Thread: WM16 help reqd
01/06/2020 22:36:06

Hi if you remove the screws from the end plates on the end of the bed you can slide the bed so far along till you can see the nut be carfuly how far you push the bed and if you need to push it over three quarters make sure it is supported with some wood or other packing. Let us know what you find please. If you have a scale fitted be careful that you don't damage it it may need removing first.


Thread: Help needed for screws - Fishing Reel
01/06/2020 11:33:41

Thanks for showing results nice job. So many things are started on here and you never see the end job.


Thread: Optical Chucks
30/05/2020 23:04:25

When I worked we used a 3R centering microscope it fitted into a collet or chuck.



Thread: Silver soldering boiler
29/05/2020 17:16:24

I made a jig pattern to bend and hold the heat shield brass plate. I made it in wood so I can clamp the brass plate, when it gets here, and bend it round and drill and flange for brackets.




I drew the radius on the end and used a ball nosed cutter to shape the curve small step by small step then rip off small cusps with sand paper. The groove in the centre is to clear the centre bushes and the brass will be bent down to fit the boiler. It did make a bit of a mess which took about an hour to clean up.


Thread: Thread cutting - Apron does not engage with the lead screw
28/05/2020 07:03:12

Hi lathe-argic welcome to the forum. Where are you based it helps as perhaps someone near could give a hand or a local to you supplier can supply materials etc. Even with the virus problem it is possible to do a video connect to see what the problems are. What are you interested in making.


Thread: Silver soldering boiler
28/05/2020 06:46:31

Hi Geoff. I have ordered the burner from Forest classics and the safety valve as I thought it would save time but it hasn't come yet.


26/05/2020 22:59:25

Made a bit of progress on boiler and made a small drain cock for condensate in chimney, made chimney and started mounting boiler and engin.











Edited By David George 1 on 26/05/2020 23:01:24

Edited By David George 1 on 26/05/2020 23:02:18

Thread: [Project 4] Sine plate
24/05/2020 22:51:17

we had a large sine table at work about 3ft by 4ft and the top plate was 3 inch thick. we made standard size bars to go under the plate to suit all the jobs we did from 5 deg to 45 deg. It was made of ground plate P20 I think, and was covered by a pattern of tapped holes to clamp jobs on for milling. You had to use a jib crane to lift the top plate to use it but it did loads of jobs for tool making moulds etc.


Thread: Silver soldering boiler
22/05/2020 16:52:58

Made the boiler end support plates. I decided to make them from stainless steel perhaps could have been a little thinner material, 1.2mm, but I managed them in the end although I had to put a groove down the fold line to get a nice bend.


Rotary mill end top radius.


Bore hole for boiler.


Bent ready to try.


These are finnished now.


Thread: [Project 3] Dickson T1 Tool Holder
22/05/2020 13:46:15

This is a drawing of a standard toolpost using a screw with a plain shank to check sizes from to make sure that the clamp mechanism works the same on all replacement pieces.



Thread: Merryweather Steam Fire King self propelled
22/05/2020 07:09:04

Hi Werner nice to see you still safe and your magical engine still working.


Thread: Using large dies
20/05/2020 07:47:37

The pipe thread set I have has separate blades which are adjustable and when I worked on a lathe this style of threading head was used for larger threads over 1 inch and were fitted to tailstock MT 4 which released when the tailstock was stoped by saddle which was hit by sliding tailstock.



Thread: Stabilising a Milling Machine
19/05/2020 14:25:13

just get some resin anchor fix from your local builders merchants and some threaded rod washers and nuts. Drill the holes through the base into and even through the concrete the clearance for the threaded rod. clean out the holes to get rid of dust etc. then fill the holes with the resin ( read label on cartridge for instructions) and push in the threaded rod, which has to be clean and grease free, twisting as you push to get a good coating. The rod will become part of the concrete without stressing the hole and will never come out. the threaded rod has to be cut off flush to the floor if you ever need to move the machine but it will never fall over. I have used this for many pieces of machinery from an offhand grinder to large CNC milling machines up to 50 tonne and recommend it as the safest and easiest method to fasten down machinery.


Thread: Milling spindle motor
19/05/2020 09:14:34

I recently made a toolpost spindle but mainly for drilling etc.


It has a variable DC motor driving a 2 to 1 ratio tooth belt and pulley.


Thread: Sharpening Fine tooth slitting Saws
19/05/2020 07:51:17

You can try here not connected but remember using them at work for grinding carbide for jigs.


Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Latest Forum Posts
Support Our Partners
Eccentric July 5 2018
Allendale Electronics
Eccentric Engineering
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest