By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for vintage engineer

Here is a list of all the postings vintage engineer has made in our forums. Click on a thread name to jump to the thread.

Thread: Childhood diseases
23/05/2019 13:35:03

When I had mumps, I could put my testicles in a wheel barrow!

Thread: Bookpress 5tpi Square thread help please!
23/05/2019 13:32:57

You will need to grind your own tool to cut the thread. I am not familiar with Myfords but it's all down to getting the right gear train to drive the leadscrew.

Thread: An old Shaper found in Phuket Town
21/05/2019 17:01:08

Is it for sale?wink

Thread: Painting
21/05/2019 16:54:01

If you use bbq paint, when it's dry you can buff it up. I think it has graphite in it.

Thread: stamford show vandals
21/05/2019 16:46:32

And you think we live in democracy?

 

Having lived in one party state countries they were a lot safer and you knew where you stood with the judiciary!

 

 

Posted by duncan webster on 21/05/2019 11:35:47:

So do you want to live in a country which is hardly a functioning democracy, and scores 4 on a scale of freedom rating (7 is worst, 1 is best). UK rates at 1, same as Germany and Netherlands, slightly higher than France which is 1.5

 

Edited By vintage engineer on 21/05/2019 16:51:02

Thread: HSS or CS taps and dies
21/05/2019 10:19:18

Taps are quite easy to sharpen and can be touched up with a stone.

Thread: stamford show vandals
21/05/2019 10:15:33

Singapore is a very civilised country and very safe. This is because the punishments are quite severe but everyone knows what will happen if they break the law. These yobs would be caned with a ratten cane. There is very little crime in Singapore and this due to the public being full aware of the punishments and they fully support them.

Outside Changi Prison there are signs stating all intruders will be shot dead and they aren't joking!

21/05/2019 10:15:32

Singapore is a very civilised country and very safe. This is because the punishments are quite severe but everyone knows what will happen if they break the law. These yobs would be caned with a ratten cane. There is very little crime in Singapore and this due to the public being full aware of the punishments and they fully support them.

Outside Changi Prison there are signs stating all intruders will be shot dead and they aren't joking!

21/05/2019 10:15:32

Singapore is a very civilised country and very safe. This is because the punishments are quite severe but everyone knows what will happen if they break the law. These yobs would be caned with a ratten cane. There is very little crime in Singapore and this due to the public being full aware of the punishments and they fully support them.

Outside Changi Prison there are signs stating all intruders will be shot dead and they aren't joking!

20/05/2019 20:23:53

When I was younger I grew up overseas and I deviated from the correct path. I was sentenced to receive 6 "Cuts" at the local Police Station with a Doctor present.

I have never strayed since and most of the people who received similar punishment didn't either! It did work and word spread around school about the results of the punishment!

20/05/2019 09:45:39

I am afraid we have become too soft. If we still had the birch there would be a lot less trouble. When you have been birched once you certainly do want a second helping!

Thread: Source of Machined Nuts
18/05/2019 08:24:05

If you make up a saturated solution of table salt and malt vinegar, soak them in this and it will remove zinc plating overnight!

Posted by Alain Foote on 17/05/2019 21:12:39:

Thanks Colin, really want unplated ones though.

Thread: Nickel Plating Brass
15/05/2019 16:55:34

Can you reverse this process?

Thread: Rudder Bushes on Boat
15/05/2019 16:52:10

Why not use PTFE?

Thread: Cutting steel to size
12/05/2019 19:29:21

I bought the Warco horizontal bandsaw. It was built to a price, but the main faults were easily rectified.

Changed the vice lead screw, nut and handle.

Added a wider plate to the movable jaw.

Sorted out the stop switch and resting stop.

Made a coolant tray and tank.

Now I am very pleased with it. Largest cut so far was 150mm square aluminium.

Thread: A dynamo question: rotation direction?
12/05/2019 10:05:25
  • If you put the field coils in the casing the other way round will not run the way you want?
11/05/2019 20:21:18

To convert an Austin 7 dynamo to 12 you just need to change the voltage regulator.

Thread: Sump Plug
09/05/2019 03:34:16

Ordinary 12 point sockets will fit square heads.

Thread: Railway sign
06/05/2019 21:20:51

The fonts are all wrong.

Thread: Parting off stainless hex bar
05/05/2019 12:28:24

Start slow until the bar is round then treat the same as round bar.

Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Latest Forum Posts
Support Our Partners
Eccentric Engineering
Eccentric July 5 2018
Warco
Ausee.com.au
ChesterUK
Allendale Electronics
Sarik
emcomachinetools
TRANSWAVE Converters
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest