By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for Brian Sweeting

Here is a list of all the postings Brian Sweeting has made in our forums. Click on a thread name to jump to the thread.

Thread: Unimat tangential tool holder
05/12/2018 22:31:47

Here is one from earlier with handrawn plans...

**LINK**

Thread: The demise of the High Street
03/12/2018 12:26:17

Let's be honest this all started years ago when the supermarkets started building outside the town centres.

We, well lots of us, started shopping there and it was followed by people complaining that their local butcher/baker or greengrocer had shut. Without the staple shop trade the town centres were bound to collapse and yet we still blame everything/everyone else about the state of our local high street.

It's not going to change back so we have to do the best that we can with what's left.

Thread: Schmidt Couplings
29/11/2018 19:01:40

Found a similar coupling in the Brammer pdf **LINK**

Look for Ruland couplings.

Thread: Mars Insight has Landed
26/11/2018 23:48:05

Danny a nice bit of family history to pass on.

Mind you, someone up there now has a list of names responsible for all the bits of litter we have been placing on the planet. The penalty notice is in the post. smiley

Thread: Space Ship leaves Earth's Atmosphere
24/11/2018 21:49:39

Excellent, what always amazes me with these ISS shots is the amount of 'debris' flying around them.

Edited By Brian Sweeting on 24/11/2018 21:50:01

Thread: 1950/60 car electronic rev counter
20/11/2018 17:35:32

Some rev counters used a feed from the alternator, normally on diesels.

Thread: “Every Boy His Own Manufacturer"
17/11/2018 12:08:59
Posted by Grotto on 17/11/2018 04:18:26:

And a complete chapter on making your own fireworks.

Don’t see that in modern books

Did you notice that the page of ingredients for the fireworks was out of focus or was it just me?

Thread: Quick release hook
14/11/2018 22:58:40
Posted by Sam Longley 1 on 14/11/2018 22:51:54:
Posted by Brian Sweeting on 14/11/2018 22:48:13:

Snip

Thanks I did not realise that pattern went that large . Wichard are notoriously expensive but I will find out the cost

Yes, I was surprised too, then again I dread to think of the load on some sheets carrying big sails in a blow.

14/11/2018 22:48:13

Plastimo do a 9000kg, swl5200kg, snap shackle, is this your idea?

Link here

https://www.plastimo.com/en/mousqueton-a-ouverture-sous-charge.html

 

Edited By Brian Sweeting on 14/11/2018 22:48:42

Thread: Coil winding
13/11/2018 14:06:54

I think that is the difference between winding a coil and winding a spring.

Thread: Lead Bearing Solder is Banned
08/11/2018 14:26:12

Thanks for that. I was interested to see that you receive visits from the powers that be.

I used to work with refrigerants, before retirement, and those in the trade were annoyed, and still are, at the complete lack of anyone from the Environment agencies showing any interest in getting people/firms complying with current legislation.

Anyway, rant over.

Thread: Noisey MEM switch
07/11/2018 23:58:14

It could also be the operating coil beginning to weaken, depending on age of course.

Edited By Brian Sweeting on 08/11/2018 14:15:25

Thread: Gas demand valves
05/11/2018 22:56:46

Second thoughts - plan to build your own here....

**LINK**

Tecumseh needle valve and diaphragm are still available via Google search.

Edited By Brian Sweeting on 05/11/2018 23:02:08

05/11/2018 22:23:07

Found this set of plans and parts from America, any use?

**LINK**

Thread: Small Hex Fastenings
05/11/2018 22:14:00

It seems that you have been given some options but not knowing where 'local' is made it hard to answer for me, sorry.

Thread: Given the Elbow
23/10/2018 15:01:16

Not sure if this is the same but it looks like it - **LINK**

Thread: Storing Machinery In Damp Conditions - Advice Please
23/10/2018 14:53:05

+1 for ACF-50, used to use on my motorcycle and last winter used it on my mini-lathe sat in the shed in the garden.

Also gave the hand tools a wipe over with it.

Thread: which compressor
23/10/2018 00:09:23
Posted by Howard Lewis on 20/10/2018 22:13:18:

Are automotive air con compressors compressing gas or liquid?

The usual advice is to run the air con on the car for about 5 minutes each week to keep the seals lubricated. That suggests liquid rather than gas. Or maybe the refrigerant is below its critical temperature, and when compressed it changes to liquid, and that is what lubricates the seals.

Anyone to enlighten us?

Howard

All refrigerant comoressors, electric or mechanical pump vapour, if they pump liquid they very quickly destroy tgeir valves or con-rods.

It is the oil mist mixing with the refrigerant that provides the lubrication to the seals etc.

Thread: Pumping water up a hill
22/10/2018 23:59:23

Not sure if this is the best option but have you looked into 'ram pumps'. These use the water itself to perform the pumping action.

This **LINK** site is commercial but will give you an idea of what can be acheived.

Thread: Unknown Lathe
20/10/2018 14:30:02

Sorry, can't see it from here so wouldn't like to guess.

Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Support Our Partners
Eccentric July 5 2018
Eccentric Engineering
Advertise With Us
Meridienne Sept 2019
Ausee.com.au
TRANSWAVE Converters
ChesterUK
Warco
emcomachinetools
Allendale Electronics
Subscription Offer

Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest