By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for Brian Sweeting

Here is a list of all the postings Brian Sweeting has made in our forums. Click on a thread name to jump to the thread.

Thread: What Material for 5C collet Rack
20/08/2017 16:08:53

I have a range of ER25 collets which I store in an ice-cube tray.

I then screwed it to the wall with a wedge to kick the bottom out.

Similar from web trader http://www.amazon.co.uk/Kitchen-Craft-Colourworks-Cube-Tray/dp/B004ZKUHEK

Edited By Brian Ess on 20/08/2017 16:12:37

Thread: Health and Safety shoots down entire RAF
17/08/2017 23:02:30
Posted by Cornish Jack on 17/08/2017 19:42:24:

Brian Ess - That was the AAIB's verdict. There are some interesting variations on possible causes discussed on a couple of threads on the Professional Pilot's Rumour Network - www.pprune.org. That notwithstanding, be it incompetence or technical failure, the results are best avoidedsad

rgds

Bill

Wholeheartedly agree with you.

17/08/2017 15:26:36
Posted by Cornish Jack on 17/08/2017 10:13:10:

As pointed out above, the Liberal party have nothing to do with this - but don't let that upset your prejudices!!

Having, as a professional, had to deal with the results of aircraft 'failures', the dictum of "Safety is no accident" sits much better with me than the "Oh, Boo Hoo, some nasty person has stopped my toys being allowed out to keep me amused for ten minutes"angry 2 Has the memory of the Shoreham Hunter carnage really faded that quickly?

Some VERY odd values around!

rgds

Bill

I thought Shoreham was due to pilot error not mechanical failure.

Thread: 1/6" x 28tpi tap & die.
13/08/2017 14:11:57

Have you tried Wiseman Threading Tools, **LINK**

They offer a "specials" service.

Thread: Spiritburners
05/08/2017 22:41:31

Do they burn with a good flame?

What configuration are the wicks in?

Thread: KWh question
05/08/2017 15:39:40
Posted by Muzzer on 05/08/2017 11:16:36:
Posted by Andrew Entwistle on 04/08/2017 21:19:17:

One feature that a smart meter provides to the supplier is the ability to disconnect the supply remotely (avoiding the need to gain access to the property). Just like with direct debits one has to trust that the institution will play by the rules, but it is possible to end up in a weak position if things go wrong e.g. following a malware attack.

Edited By Andrew Entwistle on 04/08/2017 21:23:02

Any evidence to support this assertion? As far as I've seen so far they simply measure the voltage and current. If they also had to incorporate a 200-300A contactor, that would be a different beast.

Lots of opinions and half truths as ever.

Take a look at a few manuals if you want to understand what they do rather than ignorantly opining about them.

Murray

Checked out a Smart Meter manual as you requested and it states..

(Quote)

Contactor Disconnect

The main 100A contactor can be  disconnected locally or remotely by the Utility.

This can be driven directly or driven by the meter at load limiting thresholds

(endquote)

Whose half truth ?

Edited By Brian Ess on 05/08/2017 15:40:18

Edited By Brian Ess on 05/08/2017 15:41:26

Thread: I.T
03/08/2017 19:48:13

Went over to Open Office years ago, great suite.

Thread: Ideas on how to repair a cast iron T slot
03/08/2017 16:54:50

post deleted by me

Edited By Brian Ess on 03/08/2017 16:55:22

Edited By Brian Ess on 03/08/2017 16:55:56

Thread: Choice of avatar
01/08/2017 20:25:22

You can't beat a good Staffie.

Thread: Who made this?
31/07/2017 23:39:48

The boilers not theirs but the speed governor looks like a Wilesco model.

Edited By Brian Ess on 31/07/2017 23:40:47

Thread: Is Knurling a health hazard?
31/07/2017 23:23:02

This type of thread always gets a thumbs up from me, you begin to realise the vast and diverse knowledge base that we have contact with now-a-days within a relatively small family of like minded people.

If I can add my little towards skin care, a few years back my wife started getting cracked skin on her hands, very similar to 'old Harry's 'ands' from years gone by. This we found was due to a preservative in hand washes and hand creams, also shampoo and cosmetics.

The product is called methylisothiazolinone , see **LINK** for more info. Since we removed this from our house and usage both of us had improved skin conditions.

Edited By Brian Ess on 31/07/2017 23:23:51

Thread: Motor rotation
31/07/2017 20:39:39
Posted by sean logie on 31/07/2017 20:06:07:
So correct me if I'm wrong .... the brass tab connectors on the motor are to be left in the configuration they're in just now . Sorry for being dumb 😁

Sean

If you look inside the terminal lid there should be a picture/graphic showing the link settings for star and delta.

Thread: Source of Silver Steel
29/07/2017 20:53:12

Slightly off topic but having looked at the OP link to GROUNDFLATSTOCK.COM they have useful heat treatment data sheets for all of the products.

Thread: Motor rotation
29/07/2017 17:37:39

Agreed, it is a three phase motor, it can be run on 230v single phase but will probably overheat, as you have found.

The single phase method is called the Steinmetz method. Our friend Google will find quite a few useful results.

28/07/2017 22:19:19

Wiring schemes here...

 

**LINK**

Thread: Heat resistant gloves for a little person
21/07/2017 23:33:47

Childrens work gloves here, do a search on 'children'

**LINK**

Thread: Logging in
15/07/2017 22:57:53

Have you also ticked the "remember me" box?

Thread: Conversion table
15/07/2017 22:50:13

Tap Drill sizes..

**LINK**

Drill / metric sizes

**LINK**

Also a calculator if it helps.

http://www.guhring.com/Tech/TapDrill/

Edited By Brian Ess on 15/07/2017 22:55:26

Thread: Chuck lubrication
14/07/2017 20:25:32

As a simple minded small lathe user I would query using grease in the chuck due to greases ability to hold onto swarf.

I know that chips will stick to oil but have more chance, perhaps, of being flung out when the chuck is rotating.

My small chuck has an oil hole not a grease nipple.

After I've oiled my chuck I wrap it in kitchen paper towel, held on with an elastic band, and run it at high speed. This gets the excess oil out quite well.

Thread: Casting brass
11/07/2017 17:47:59

Graphite crucibles are good, general ebay result from google.....

**LINK**

Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Latest Forum Posts
Support Our Partners
Warco
Allendale Electronics
emcomachinetools
ChesterUK
Eccentric July 5 2018
cowells
Eccentric Engineering
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest