By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for Brian Sweeting

Here is a list of all the postings Brian Sweeting has made in our forums. Click on a thread name to jump to the thread.

Thread: Warco BH600G carriage stop
30/10/2017 16:01:34

Nice job.

Thread: Brass shaping
30/10/2017 13:20:39

Would a Dremel with a burr head cut out the 'O's.

Thread: A bit of math - lenght of belt in pulley systems.
28/10/2017 12:30:29

Lots of calculators out there but if you want to do it longhand then here it is ....

**LINK**

Thread: Steel hardness numbers
26/10/2017 22:46:11

As Norman says, an angle grinder does the business, certainly did for mine.

Thread: Small Number Plate Required For 2" Minnie
25/10/2017 20:09:56

These people might be worth a phone call perhaps...

 

**LINK**

Thread: How do I check the capacitors on my Warco Mill?
19/10/2017 15:17:40
Posted by Neil Wyatt on 19/10/2017 14:17:40:

A start capacitor may not have enough capacity to kick the needle of a multimeter.

If you carefully short it through a large resistor that should do the job without causing any drama.

Neil

 

If you have a simple electric soldering iron then they are very good for discharging capacitors.

Thread: Electric chain hoists/carriages
18/10/2017 22:50:27

I haven't investigated fully myself but.... could you use a modified electric garage door motor/drive unit to move your hoist along it's support rail?

Thread: WM180 Saddle adjustment
18/10/2017 16:23:53

If you look in the manual you should see an exploded diagram of the saddle.

Towards the front there is shown a strip of metal with three grub screws with locknuts, these are the adjustment screws.

You will need to remove the front apron to gain access.

Thread: Black 5 ready again to run
18/10/2017 14:02:46

Well done, mind you six adults could have needed a diet

Thread: Torque problems: lathe, 3-phase, inverter...
17/10/2017 15:55:12

What's it like if you disconnect your improvement control and revert back to the original system of operation?

Thread: Linisher cuts out, what to do...?
17/10/2017 13:18:36

Well done Richard, glad it's all working and thanks for the update.

Thread: Bolts & Setscrews Help Needed
15/10/2017 12:19:36

I believe in your case that the dogtooth is simply to aid the installation of the bolt in a production line. It guides the bolt into the hole for a faster fit.

Thread: Starter Switch
14/10/2017 18:47:03

Well done Andy, it must be tricky getting it going again with so many people in the workshop with you. laugh

Thread: Black 5 ready again to run
13/10/2017 23:31:16

Fingers crossed for you, not that you really need. Sounds like you've got all the bases covered.

Hope it's a good day.

Thread: Starter Switch
13/10/2017 14:25:24

It is often safer to remove all previous wiring and start afresh following a wiring diagram.

12/10/2017 19:46:21

SOD, yes that is correct, good picture.

Thread: Spring is in the air
11/10/2017 22:10:21

Quick internet search brings up quite a few but this one seems promising...

**LINK**

Thread: Starter Switch
10/10/2017 20:41:07

Ian, thanks, I stand corrected.

The reason for using all three overload contacts is because if one contact is unused there will be an imbalance across the three. Not so important with the older style overloads but the newer ones can be more sensitive. All overload manufacturers schematics will show all three contacts in use.

10/10/2017 20:08:48

Ian, the purpose of looping through all of the poles is to get better performance of the overload.

Did I suggest that the feed should go through the overload first?

Unequal loading can cause nuisance tripping.

Your assumption that the original poster, Andy, is unable to assimilate the schematic is rather condescending don't you think?

10/10/2017 19:01:26

Wiring diagram shown here...

 

**LINK**

Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Latest Forum Posts
Support Our Partners
cowells
emcomachinetools
Warco
Eccentric July 5 2018
Allendale Electronics
ChesterUK
Ausee.com.au
Eccentric Engineering
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest