Here is a list of all the postings John Baron has made in our forums. Click on a thread name to jump to the thread.
|Thread: Countersink choices|
Don't do that, you will quickly ruin it !
Weldon single hole countersinks have a tapered cone ! You can see it if you use a pointer aligned with the edge of the cone and rotate the countersink. There is about 20 thou of taper on them.
Edited By John Baron on 30/01/2019 11:18:07
|Thread: Hemingway Knurling Tool|
I would have glued both pieces together and put them in the four jaw on the lathe, drilled to remove the waste and then bored both holes to size.
However its an interesting technique that you have used. I'm watching with interest.
|Thread: Flycutters: help to understand 3 different types|
Very good effort !
First thing I noticed from your first picture, you have far too much tool stick out. Rigidity is the thing here. I also notice that you have the spindle secured with two nuts. Whilst its hard to see on the picture of mine there is no spindle below the bottom of the disc. The spindle on mine was pressed into a bored hole, and I also used superglue to make sure that it did not move. Whilst not absolutely required, I also faced off the underside whilst holding the spindle in the lathe chuck.
I did a lot of playing about with tool bit shapes. The rounded edge seen protruding through the disc is the one that I use for alloys. There is only about five or six degrees of rake and the front face is virtually flat.
The toolbit for cutting steel is quite hooked. I basically copied my lathe tools.
Last thing ! Check your mill tram. Under ideal conditions you don't want the cutter taking more off on one side, this is most noticeable on a long cut when cutting in one direction and the cutter is taking a shave off at the other side.
I agree ! But at the time I had only recently got the mill, so it was very much an exercise to see if I could make one. I've had a Myford S7 for a long time, so making a suitable fly cutter was the easy part.
I agree ! All sorts of things can be cut with a flycutter.
This is a couple of pictures of a dovetail slide that I made that way. The really hard part was making sure that both the male and female parts fitted together properly.
I admit that I did cheat a little. After making the male half, I took a slice off the end and used it as a template when making the female half. They are a nice fit and slide together well.
The brass screw on the left of the top picture is for locking the slide.
The screw on the bottom picture drives the two parts.
Edited By John Baron on 07/12/2018 12:10:44
All the fly cutters seen in this thread will work ! The only one that I would not use is the boring head.
The primary requirements are rigidity, and balance ! Out of balance forces cause various issues, vibration being the least desirable. A fly cutter has to be able to encompass the work area or you have to make multiple passes. Clearance, you don't want to collide with any protruding obstacle, hence the angled cutter type.
This is one of mine. 3" inches in diameter, 20 mm thick, 20 mm spindle. A heavy rigid body and spindle. Well balanced, and a good flywheel effect. Particularly important if making interrupted cuts. I can take a 1 mm DOC in mild steel at a 150-200 rpm. The tool bit in this one is 5/16" square HSS.
Edited By John Baron on 06/12/2018 19:19:27
|Thread: Arduino DRO|
FWIW every HP inkjet printer has an linear optical positioning system that is easy to get at and provides directional information. The reader head, whilst different in size to say a slot opto, is very similar electrically. Without checking the technical data sheet for the optical reader head I don't know how fine the steps are, certainly the tape is at least 200 lines to the inch.
|Thread: ML7 Quick change suggestions|
Why not make one ? The Norman Patent tool post is a good project !
This is mine, sized for the Myford lathe.
|Thread: Cutting a keyway without a broach|
Why don't you try it !
I'll guarantee that you can't pull it out by hand !
That retaining method has been around for a great number of years ! One of its uses is to retain two round shafts that are not in perfect alignment and provide drive from one to the other. You can find examples of this in some of the old radios of the 20's and 30's. I do believe that its used in some rotary tools today.
|Thread: Myford ml7 tools size|
If you have the ability, make a "Norman" patent tool post ! I made one for my Myford S7 and can use from 1/4" inch up to 1/2" inch square tool size. Most of the work building one is turning and threading. I posted a picture of mine a short while ago. I also have the drawings based on the original patent by Van Norman.
Its one of those things that I wish I had made years ago. In fact Myford actually produced and sold the ML3 and I believe ML4 lathes with one already fitted.
Forgot to add I use HSS tool bits, the Myford doesn't really have enough speed for making best use of carbide.
Edited By John Baron on 10/11/2018 20:11:43
Edited By John Baron on 10/11/2018 20:12:32
|Thread: Cutting a keyway without a broach|
Yes I published mine in 2010, so that would have been just before you're article. The similarity prompted my reply to the post. Since I didn't even know that you're web site existed.
I recall that the method of retaining the toolbit caused some interest at the time !
It seems that great minds think alike. I'll have to go and have a wander around and see what else you have done
That tool is based on the one that I published on another forum some years ago
One of the things that makes it unique, is the method I used of retaining the cutter.
|Thread: inside an induction hob|
I agree ! Why pay them money to make more money from your scrap !
There are a lot of very nice and useful components in a lot of the stuff that we have to pay to get rid of. The local scrapyard will gladly take this stuff of your hands for free, simply to survive.
The last lot of electronics scrap I took to the scrappy, I got £250 for 1/2 a ton. Mainly computer PCB's.
|Thread: Myford Super 7 Serial Number Missing|
It could be one of the Taiwanese clone Myfords, or just the bed and rebuilt.
|Thread: Myford QCTP Recommendations|
I hadn't noticed the spelling error !
Thanks for pointing it out !
|Thread: Power feed for a mill.|
I made a mill table drive using a salvaged car window wiper motor. It can easily be powered from an old computer PSU. Using the gearing that I used, at 7 to 8 volts it takes about 2 amps.
The white knob pulls back to allow direction changes with a neutral position in the middle. It is a simple dog in a slot mechanism. The wiper motor is dual speed, not that its needed since I actually use a variable voltage PSU and can crank up the voltage to 30 for fast traverse if I need to.
|Thread: Myford QCTP Recommendations|
Might pay you to drop me a copy of the article then !
I have a complete set of drawings based on the original patent. Though I have published my design in a number of places.
I've just made a "Norman patent toolholder for my Myford S7B. I should have done this years ago.
No modifications to the lathe, just removing the old tool holder and replacing it with a 38 mm diameter post. I also made a new nut to get rid of the ball handle.
|Thread: Bench grinder improvement mod.|
That tiny lip becomes an issue with the cheap nasty monkey metal flanges that seem to get supplied with most grinders nowadays. A good close fitting washer works wonders, extending the bore of the washer is even better !
Better still is facing the washer square actually on the grinder shaft.
Don't forget to use blotters on each side of the wheel.
|Thread: More Scam from the Scum?|
Don't get taken in by this crap ! This scam has been doing the rounds for a little while.
But just in case a bit of tape over your camera and mic will solve any issues with being recorded and videoed.
Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!
You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.
Click THIS LINK for full contact details.
For subscription issues please see THIS LINK.