By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for mark costello 1

Here is a list of all the postings mark costello 1 has made in our forums. Click on a thread name to jump to the thread.

Thread: 3 Jaw self centering ER chuck
19/02/2019 20:58:50

EXCELLENT!

Thread: New coffee maker - disgusting taste!
17/02/2019 20:13:20

Is Tim Horton's acceptable? Like their coffee.

14/02/2019 18:01:46

At the risk of a public flogging, I have a question from across the pond. The only Tea I have experience with is Lipton, is that anything remotely like what You Chaps drinkg?

Thread: print-offable and laminatable chart
05/02/2019 21:13:57

What would be the thread depth for 569 tpi? Where can I get a tap?

Thread: Old screwdrivers - any use as a materials source?
04/02/2019 19:44:25

If You need a tommy bar one with a nice handle works well.

Thread: Testing for isolation
02/02/2019 17:53:49

Worked with a chap who undid a 2000 volt extension cord. He said it blew out 4 caps from His teeth and did a long list of damages to Him. Took 2 years to recover,thought He was careless.Found out later some one plugged in the other end.

Neighbor had a 440 transformer located on His house, put a ladder upon the house to paint it, the ladder slid and He hit the 440 line and it burned all the hair off His body. Docs said the only thing saved Him was He was a weightlifter and had enough strength to last through the initial recovery process.

Thread: The Diamond Tool Holder
26/01/2019 19:38:36

I have made a carbide tool bit to use in a tangential tool holder. I have used it on hard plastics. I have not used it on steel yet.tangential carbide tool.jpg

Thread: Chinese postal charges
11/01/2019 23:18:02

Myself and the Wife working full time did not get close to $61,000 a year. I would have had the means to afford an overseas subscription to the excellent Magazine the fine People who support this forum sell. How's that for sucking up. (I realize the exchange rate is not Their fault.)

Thread: Snap rings for the new year
03/01/2019 20:44:29

Is that in Metric?

Thread: Idea for a cutoff tool
20/12/2018 17:47:37

Will get a better picture, but it is just a home made tool holder with 2 bolts holding a bottom extension in place. Everything machined together after assembly.

Thread: which parting tool
19/12/2018 14:40:32

Well, I just started a thread in the General section showing My solution. Combines the best ideas of both.

Thread: Idea for a cutoff tool
19/12/2018 14:37:15

100_0824.jpgI have made an adaption to an insert cut off tool holder that solves the snatch and break problem with these tools. I have mounted it upside down with a shop made tool block holder. It works very well preventing wrecks by sliding up when it grabs. The quick change tool posts are made to have the main thrust of forces directed down with no relief possible if there are problems. This tool holder will slip up saving the blade.100_0823.jpg

Thread: What material is it
18/12/2018 20:54:05

Could be Beryllium Copper.

Thread: How far to be off tool centre before a turned finish becomes poor?
15/12/2018 14:49:56

Across the pond some of us use pallet strapping as shims, some is .020, some is .023, and the biggest is .030.

Thread: Telephone / Internet Scams
14/12/2018 19:45:45

I answer with either similar to "Fairfield County Sherriff's office, fraud division," or act like I am getting My butt kicked.

Thread: It's not rocket science
13/12/2018 22:02:04

The meteorite I just turned was so hard it must have been heat treated in the sun, and quenched in the shadow of the moon.

Thread: What did you do Today 2018
13/12/2018 21:57:49

If You are getting negative rake with the Drill Doctor, just slightly loosen the collet and turn the drill bit slightly clockwise (I think) and tighten it up and try again. If it's worse then it goes the other way, I don't have My notes here with Me at the moment.

Thread: How does solder stick ?
07/12/2018 20:50:23

Since Mike likes to live dangerously it begs the question- Are there any Members here of the female persuasion?

Thread: Space Ship leaves Earth's Atmosphere
25/11/2018 16:15:02

We seen a shuttle launch from about 200 miles away, it was about as bright as a road flare around 300 yards away.

Thread: Deep-Well Ejector....
21/11/2018 18:10:11

Is this something a back yard hobbiest could cast at home?

Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Latest Forum Posts
Support Our Partners
Eccentric Engineering
Ausee.com.au
TRANSWAVE Converters
ChesterUK
cowbells
Meridienne oct 2019
Eccentric July 5 2018
Warco
Allendale Electronics
emcomachinetools
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest