By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for mark costello 1

Here is a list of all the postings mark costello 1 has made in our forums. Click on a thread name to jump to the thread.

Thread: Imperial Spanner and Socket advice for a metric person
14/02/2015 16:21:34

Just wait till You get an Imperial thread with Metric head and need to replace the bolt or nut.

Thread: Todays update from Bodgers Lodge
12/02/2015 15:12:03

Why would they insist on speedo's? Inquiring minds and all.........Also found a place to stay away from. Order eye bleach if going there!

Thread: What is this
11/02/2015 15:27:30

Part from the DoomsDay Clock.

Thread: Engineers level
10/02/2015 17:01:37

Worked with a chap that was a mmachinist in the U S of A Navy. The lathe He ran was 90' in length. During rough seas He was not allowed to use it as You could watch it flexing during the wave motion.

FIL used to watch W+S #2's being unloaded in the winter by attaching them too electric poles and driving off with the trailer, letting them fall on frozen ground, with no apparent difficulities later.

A w+S #2 He personally ran for years was involved in Anchor Hocking plant fire. The floor burned through and the lathe fell into the basement. After the fire was put out the lathe was pulled out and sent out and rebuilt used many years after that.

Thread: Todays update from Bodgers Lodge
10/02/2015 16:46:54

We were told at a meeting that some Government (USA) agency had to have a shelf life date per regulations. So they started putting it on all products.

Thread: Spreadsheet Machinists Toolbox
27/01/2015 15:35:01

One thing
I was taught to determine the speed of a cutter was to spin it up until You could just see the flutes as they rotated. It's conservative. This is simplified but may save a beginner a cutter until they get some experience. Works better with bigger cutters as they are easier to see.

Thread: Vanishing local shop outlets.
25/01/2015 18:22:34

We have a well known hardware store in town, been there forever. If You want anything now they hand You a catalog and tell You to find it and they will order it in when the order is big enough. Why go to them? Might as well order from the comfort of My chair and bypass the trip in town and waiting.They wonder where their business is going.

Thread: Parting On a Hobby Lathe
08/01/2015 16:00:03

I have a 14 1/2" South Bend lathe, paring off with a normal parting tool in the front is an exercise in futility. An upside down parting tool on the front side makes it painless, I even have a screwed on chuck and am being careful.surprise

Thread: Colchester Student. Surfacing
07/01/2015 16:50:27

The more You do, the more You learn. It's a vicious circle that leads to needing more machinery. Don't ask...........

Thread: Who might have made this?
10/12/2014 17:02:53

How does it work? Never seen one before.

Thread: Re-tapping damaged thread
06/12/2014 14:55:07

Most permanent solution if possible would be to use a stud and nut to put the wear on the stud and not on the threaded hole.

Thread: Brain fade!
04/12/2014 16:06:51

Co worker gave a friend a left hand drill bit to sharpen, He sharpened it several times and it still would not cut. They finally told Him the problem out of boredom.

Thread: Help needed with Spark Erosion
25/11/2014 16:02:33

Have You tried turning the tap with a pair of small wires, not stated anywhere in a previous message? May not be all that tight.

Thread: more youtube videos to watch
23/11/2014 19:50:41

Keith Fenner, Keith Rucker and Abom79 are all good video makers also.

Thread: Bernzomatic spares
01/11/2014 14:03:51

Damaged beyond repair on a machinist site? Cannot comprehend? wink

Thread: Loctite wheel to shaft
27/10/2014 13:53:48

I had a flywheel get loose on a mid size chain saw. Spun the hole out moderately bad. Saw was junk with no spares longer available. Put couple drops of 242 on the shaft and let it setup. Lasted 20 years until wore out everything else.

Thread: Free Plastic
06/10/2014 23:24:59

I am from across the pond. Could You please put Me on Your list.

Thread: Culinary interlude
22/09/2014 21:20:14

Do ostrich eggs taste the same?

Thread: When does a beginner cease to be a beginner?
10/09/2014 15:17:46

Depends how soon the next mistake is.

When You can help out another fix THEIR mistakes.

Thread: Stabilizing pins.
06/08/2014 14:06:27

Would a super glue work? Then get dissolved off later.

Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Latest Forum Posts
Support Our Partners
Allendale Electronics
cowells
Warco
ChesterUK
Ausee.com.au
emcomachinetools
Eccentric July 5 2018
Eccentric Engineering
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest