By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for Grizzly bear

Here is a list of all the postings Grizzly bear has made in our forums. Click on a thread name to jump to the thread.

Thread: Dremel 4000 motor brush replacement
26/05/2016 20:54:46

Iain,

Google​ and or YouTube.

Regards, Bear..

Thread: electric - measuring the kwh for my workshop
28/04/2016 19:45:18

Frank,

A few months ago I changed the battery, now the first "auto" time does not work in auto (does in manual). Another £50 worth of rubbish.​End quote. If your timer operates in a similar fashion to plug-in timers, try switching it from ON to AUTO, rather than switching it from OFF to AUTO. Good luck.

Regards, Bear..

Thread: Interesting Machines
16/04/2016 20:28:49

Saw these, and thought of you!

I like the WD40 can.

Regards, Bear..

**LINK**

http://www.allaboutcircuits.com/news/three-awesome-maker-tools-that-arent-3d-printers/

Thread: Bridge Rectifiers
16/03/2016 20:07:31

Hi Norm,

Can you compare the old bridge against the new one, with your DVM.

If they are identical, then suspect fault elsewhere.

Regards, Bear..

Thread: chocolate block jumpers
03/03/2016 21:01:12

Duncan,

eBay,

http://www.ebay.co.uk/itm/6A-12-Way-Block-Plug-In-Terminal-Strips-Connector-Blocks-Male-Female-/151974470598

Regards, Bear..

Thread: Advice sought
02/03/2016 19:05:37

Google is your friend, several suggestions on getting access.

Regards, Bear..

Thread: Oil reservoirs
04/12/2015 22:52:13

Hi Chris,

3-4mm thick pressed 100% Wool Felt 60cm wide per 0.5 metre, free post on eBay.

£4.25

Search 'Felt fabric'

Usual disclaimer.

Bear..

03/12/2015 18:01:42

Hi Chris,

Mucho felt on the 'net.

http://www.jaharrison.co.uk/products/felt-products.asp

To name one. Usual disclaimer.

Bear..

Thread: Clearing out a workshop
30/11/2015 18:37:51

Nice lot of well loved machinery, brings a tear to the eye.

I'm filling up, sniff.

Regards, Bear..

Thread: Screw cutting Advice
06/11/2015 21:53:01

Geoff,

Put thermal fuse/cut-out in the freezer, restored it for me!

Bear..

Thread: Knurling Wheel 'Pins'
30/08/2015 18:49:33

Hi HasBean,

How about a 'Roll pin'

**LINK**

Regards, Bear..

Thread: Stainless Steel Pipe
05/05/2015 21:22:35

Neil,

Add a little cement to the sand, no need for a plug.

Bear..

Thread: 5/32 x 40 tpi unions for 1/16 pipe
24/03/2015 20:39:32

Hi Dougie,

**LINK**

Regards, Bear..

Thread: Todays update from Bodgers Lodge
06/03/2015 19:23:06

Hi JS,

Always good to get a glimpse of the real world. Please continue to post.

I'm still chuckling with regard to the Blidgeport.

Regards, Bear..

Thread: Woodwork Router Advice
06/03/2015 19:10:25

Hi Wallace,

Router Handbook, Router Jigs & Techniques. Both by Patrick Spielman (USA).

Regards, Bear..

Thread: Workshop visitors
21/02/2015 16:51:31

Hi Everyone,

Talking of traps, ensure all traps are anchored. Not only will it stop your traps disappearing, but will allow you to despatch any wounded prey.

Regards, Bear..

Thread: Designspark 2.0
20/12/2014 17:57:05

Nice, Ady1

Question for J.S.

John, How did you get the knurls/finger grips on those brush caps. Nice work.

If the answer is a knurling tool, my apologies for a silly question.

I'm not familiar with Corian.

Regards, Bear..

Thread: How to use a turning tool
19/12/2013 18:07:57

Hi Novice,

Picture please.

Regards, Bear..

Thread: need some of these making out of steels
08/12/2013 19:17:49

Hi Bill T1,

What about an half inch socket, as in spanner?

Regards, Bear..

Thread: Picaxe in programmable electronics
07/12/2013 16:52:01

Hi everyone,

Thanks again to all that have replied.

The venetian blind controller, I have two up and running. These are with picaxe 08M2 IC's, they have replaced the previous versions that were built using Cmos IC's.

Picaxe, I was using the Flowchart method, but when you request help from the Picaxe forum, everyone only speaks Basic.

So, I would like to get to grips with Basic, I'm happy with Picaxe, I was asking if there was anything better/easier.

Have downloaded the latest Picaxe Editor Beta. Now my USB programming cable doesn't know that it's connected to Com1, Says Com8 not connected . ( Running Win7).

Regards, Bear..

Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Latest Forum Posts
Support Our Partners
Ausee.com.au
ChesterUK
emcomachinetools
Eccentric July 5 2018
Allendale Electronics
Warco
cowells
Eccentric Engineering
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest