By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for Grizzly bear

Here is a list of all the postings Grizzly bear has made in our forums. Click on a thread name to jump to the thread.

Thread: Imminent rabbit invasion.
04/11/2018 19:39:35

Rodents teeth.

**LINK**

Bear..

Edited By Grizzly bear on 04/11/2018 19:40:32

Thread: Simplex 40 hp. From another forum
25/10/2018 18:21:05

loco Simplex 40 hp .jpgHi Everyone,

Saw this on another forum.

It may be of interest to someone. Second picture in my album (Hopefully).

Regards, bear..

Edited By Grizzly bear on 25/10/2018 18:21:57

Edited By Grizzly bear on 25/10/2018 18:24:12

Thread: Myford ML7 not running true and spirals
16/10/2018 19:09:53

V8Eng,

Thank you for adding the 'Link'. Re: Back gear.

Bear..

15/10/2018 20:57:04

Ian,

"is my lathe in what? if you mean reverse, no otherwise sorry i dont know what back gear"

Not reverse, but reduction, you have to physically put it into , or out of low gear (Back gear).

Check with the lever adjacent to the chuck.

Bear..

15/10/2018 19:52:07

Ian,

Slow speed, is your lathe in back gear?

Run-out, are the chuck jaws clean/ swarf free, this is inside the chuck.

Good luck, keep us up to date.

Bear..

Thread: volt/ammeter
06/10/2018 19:49:07

Hi Duncan,

Thanks for the update, I suspected I was pushing my luck.

I trust the case/enclosure is OK.

Good luck, Bear..

06/10/2018 14:55:40

Hi Duncan,

I'll jump in and risk losing some body parts.

Ammeter should be in series with the load.

Also I can't see the unit being happy with the red & yellow wires joined.

Regards, Bear..

Thread: Problems with a breadmaker
28/09/2018 20:47:49

Hi Bill,

Take Two:

I'm sure you worded it correctly. It was selective reading on my part.

It depends how many loaves you consume in a week * 52

With home made, you decide what goes into your loaf.

So, you are excluding mice & rat droppings/ drippings, additives etc.

The smell of bread cooking is wonderful.

Regards, bear..

26/09/2018 20:45:58

Hi Bill, ~ £90

Panasonic SD2500 Breadmaker - White

423/9781 At Argos

23/09/2018 18:27:51

We have a Panasonic SD 2500 about 4 years old, had a cheapo previously, no comparison.

+ 1 for fresh yeast, it soon goes off.

Good results with various makes of flour, usual mix is 300g strong white and 200g of wheat meal or country mix,

not sure of the name, but its coarse. Add honey & olive oil + 260ml of water.

Regards, bear..

Edited By Grizzly bear on 23/09/2018 18:32:20

Thread: Yet another parting tool question...
27/08/2018 13:25:02

Riley tool post mentioned here:

http://www.hemingwaykits.com/acatalog/Rear_Tool_Post.html

Bear..

Thread: Myford belt Tension Lever Stuck!
11/07/2018 20:54:31

Thank you, Ian & Jason. Your replies made me smile!

I mentioned safety switch, due to the fact it wouldn't start.

You learn something new every day!

Bear..

10/07/2018 19:47:04

Robert,

Is there a safety switch on the belt guard, that you may have disturbed?

Bear..

Thread: MEW 269 Temperature controller
15/06/2018 18:46:07

ALT 0176 ° ( Hold down the ALT key, then 0176)

Thread: Sleeving a shaft
21/05/2018 17:36:56

Hi Tim,

You could do four slits, with your trusty hacksaw.

Regards, bear..

Thread: Hitachi 18v battery charger
12/05/2018 22:44:19

Is this any help?

http://www.eevblog.com/forum/reviews/hitachi-lithium-battery-charger-question/

bear..

12/05/2018 22:27:25

Hi clogs,

I was tasked with a similar charger, saw the burnt resistor, long story, short, gave it back to the owner. He rang me about a week later, he had fixed it with a new resistor. he had found the info. on the 'net. I don't know the resistor value. I will look on the 'net.

Regards, bear..

Thread: What are these Now with Photo
15/03/2018 22:14:50

Dave,

The Potters Connection Ltd (Company No 06404315)
Stoke-on-Trent, England VAT No. 920919424
Tel: 01782 598729
Fax: 01782 765833
SALES TEAM: sales@pottersconnection.co.uk sales@pottersconnection.co.uk

Bear..

Thread: Plans for a 17cm Standard Rifle Target Pellet Trap
05/01/2018 17:49:01

Russ,

Buy one, work out any mods required to suit your needs, then copy it, times nine.

(Hw100 Sporter in 0.177"/4.5mm.)

Regards, bear..

Thread: Arduino Uno Programming Assistance Request
03/01/2018 17:35:55

For those of you picturing a swinging picaxe, try this:

http://www.picaxe.com/

Picaxe has a superb forum.

Regards, bear..

Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Latest Forum Posts
Support Our Partners
Meridienne oct 2019
Eccentric Engineering
cowbells
Eccentric July 5 2018
ChesterUK
TRANSWAVE Converters
Ausee.com.au
Warco
Allendale Electronics
emcomachinetools
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest