By continuing to use this site, you agree to our use of cookies. Find out more

Member postings for Chris Shelton

Here is a list of all the postings Chris Shelton has made in our forums. Click on a thread name to jump to the thread.

Thread: Micro-Weld carbon torch 1A
01/07/2018 12:52:33

img_0369.jpgimg_0371.jpgimg_0370.jpgHello All,

I picked up this unit at a boot sale this morning, was going to use the case to house the electronics and motor for power feed on my milling machine.

But looking inside I think it might be useable as a spot welder for lithium battery connections, or for resistance soldering.

The AC output voltage can be varied from 1V to 6V.

Would like to know what the originalimg_0374.jpg torch/hand piece used with it would consist of.

Can't find any info on it having searched the web.

Thread: Emco V10P carriage stop
12/05/2018 15:07:27

img_0343.jpg

Completed stop made from JohnF's plans.

Thank you John

Thread: Emco V10P carriage stop
24/04/2018 13:25:39

Thank you all for the replies, I have measured the angle of the lathe bed way and unfortunately it's 85 degrees not 90

So I am going to go the sawing and filing route, was hoping to use an end mill and create the V in the stop.

JohnF, I have sent a message with my email address, thank you for the reply and the offer of the drawings.

23/04/2018 15:02:16

I have an Emco V10P lathe, and need to make a carriage stop for it, but the bed ways are rather an awkward shape, I have included photo's and a tracing taken from the tailstock end of the bed in my albums.

I do not possess a tilting vice or a sine bar, can anyone suggest a way of making an accurate stop for the carriage please.

I do own a milling machine.

Thread: Diesel engines for miniature gauge locomotives?
25/03/2018 14:25:54

Neil, I think the car you are talking about was an Aixiam, a car dealer I carried out work for was an agent for them, I did quite a lot of electrical work on them, they could driven on a motorcycle licence.

They used a single cylinder Kubota engine, which as you say was bullet proof.

The problems really got bad when they introduced a battery powered van.

Thread: imperial rule.
14/03/2018 16:12:06

Hi a hunt for a yard stick on eBay turned this one up, item no

 
263270278507
 
HTH
 
Thread: Warco VM-16 dead
28/01/2018 13:45:20

Hi have you checked the safety switch on the chuck guard?

Thread: Drawer Liners
10/12/2017 14:05:37

Ikea Variera drawer and shelf lining sheet is 50x150cm and costs £3.93.

HTH

Chris

Thread: using an inverter to power a 3ph hoist
04/12/2017 14:04:18

Hi it is important with inverters that the connections between the inverter and the motor are direct, so you would have to use the low level controls on the inverter for up and down control.

HTH

Chris

Thread: band saw
30/09/2017 11:43:21

Very similar one on eBay item No.291639622707

HTH

Thread: inverter stick welder
07/07/2017 11:09:20

Hi,

I recently purchased the Parweld XTS 142 from eBay item No 262719324591 Cost including postage was £158, this also included a Parweld auto dimming helmet and a pair of leather gloves.

Have not used it much but worked really well, and also will work as a scratch start TIG with the addition of a suitable torch.

HTH

Thread: Can an electric power steering pump drive a hydraulic ram
11/06/2017 18:08:11

Hi, have you looked at the 12V electric hydraulic pumps used on Transit tipper trucks they usually have a reservoir, and a pressure release valve to let the fluid back into the reservoir.

Thread: Small cable connecting
02/06/2017 11:05:59

Hi, how about soldering them and heat shrink tubing, or the automotive red butt connectors.

Thread: Help from any Kennedy Hexacut Power Hacksaw owners out there?
15/05/2017 19:45:36

Hi Robbo,

Yes, Thank you that is the info I have, plus a sales leaflet describing the two models offered, one motorised and one without motor, having a V pulley fitted, instead of the flat pulley.

15/05/2017 15:41:20

Michael, I think the original belt was slightly elastic, I manage to find an automotive ribbed belt, which I turned inside out, and this has been working OK.

HTH

Chris

15/05/2017 14:31:54

 

Hi Russ,

Motor RPM is 1425, large driven pulley is 149.05 mm and motor pulley is 20 mm in diameter.

I have some instructions in PDF I will try and send them via private message.

Sorry Russ can't see a way of attaching pdf files to PM 

Will try and create an album with them 

Sorry that failed, is it ok to include them in this posting, perhaps mods could advise.

HTH

Chris

Edited By Chris Shelton on 15/05/2017 14:38:01

Edited By Chris Shelton on 15/05/2017 14:47:04

Thread: What's the most dangerous tool in your workshop
12/05/2017 10:55:01

Perhaps it was a Snap-On spanner.

Thread: Airline connectors anyone?, - Biax grinder
12/05/2017 10:43:31

Hi, I think they are called euro connectors, ebay item No.

 
252780579939
HTH
 
Thread: CCMT Carbide Insert PLAIN
10/04/2017 18:06:01

Hi

Chronos are Glanze agents, they should be able to supply them, or Cromwell tools.

HTH

Thread: Hobbymat MD65 - Milling Angle Piece
06/04/2017 23:11:22

Steve I have sent you a private message.

Magazine Locator

Want the latest issue of Model Engineer or Model Engineers' Workshop? Use our magazine locator links to find your nearest stockist!

Find Model Engineer & Model Engineers' Workshop

Latest Forum Posts
Support Our Partners
Warco
Eccentric July 5 2018
cowells
EngineDIY
emcomachinetools
ChesterUK
Eccentric Engineering
Subscription Offer

Latest "For Sale" Ads
Latest "Wanted" Ads
Get In Touch!

Do you want to contact the Model Engineer and Model Engineers' Workshop team?

You can contact us by phone, mail or email about the magazines including becoming a contributor, submitting reader's letters or making queries about articles. You can also get in touch about this website, advertising or other general issues.

Click THIS LINK for full contact details.

For subscription issues please see THIS LINK.

Digital Back Issues

Social Media online

'Like' us on Facebook
Follow us on Facebook

Follow us on Twitter
 Twitter Logo

Pin us on Pinterest